User's Manual
Inserting the SIM Card Alarm Communicator Installlation Manual
8
Mounting
Hole
Mounting
Hole
SIM Card Holder
RJ-45
Connector
(TL255 and
TL2553G only)
INSERTING THE SIM CARD
1. Remove the front cover of the SCW Control Panel to access
SIM holder.
2. Power down the panel and disconnect the backup battery
connections.
3. On the SIM card holder push gently to slide the cover
towards OPEN as indicated by the arrow on SIM holder.
This will unlatch the SIM card holder on the side furthest
from edge of the Communicator.
4. Lift up the SIM card holder from the side that is not hinged.
NOTE: The SIM card can be damaged by bending or scratching
contacts. Use caution when handling the SIM card.
5. Insert or remove the SIM card, noting the orientation of the
notches on the SIM card and the SIM card holder.
6. When inserting a SIM card, insert the card in the proper ori-
entation and gently push the SIM card holder down and slide the holder as indicated by the arrow on SIM holder, to LOCK.
7. Apply AC power to panel, and replace the panel cover.
HARDWARE RESET
The Communicator can be hardware reset by installing a jumper between Pins 4 and 5 on the AUDIO/DEFAULT connector.
ESTABLISHING A COMMUNICATION CHANNEL WITH THE SCW PANEL.
Establishing a communication channel between the Communicator and the SCW is critical to ensuring the desired operation of the two
units. The following steps must be completed during the on-site installation. Program the followingto ensure that the Communicator
and the panel will work together as intended.
NOTE: Panel Sections must be programmed at the panel keypad.
1. Enter
[*][8][Installer Code] [Section Number]
for panel programming. Record any values that are modified from their default, in the
appropriate Programming Worksheets.
NOTE: When programming Toggle Options, the toggle is ON when the number is displayed and OFF when the number is not dis-
played. (e.g., [1---5---], Toggle Options 1 and 5 are ON, all others are OFF).
2. Panel Section [167] Cellular/Ethernet Interface Communications ‘Wait for ACK’: Program value as: 060 (seconds).
3. When the communicator is installed with the SCW panel, 4 telephone number are available to backup one another. You can set up
these 4 telephone numbers to perform in one of two ways: Backup dialling or Alternate dialling.
a. Backup dialling: each of the 4 telephone numbers will make 5 dialling attempts in turn, before an FTC trouble is displayed on the
keypad.
b. Alternate dialling: each telephone number makes 1 dialling attempt before moving on to the next number, cycling through each
of the 4 numbers for a total of 5 times each. If all 4 numbers fail the 5 attempts, an FTC trouble is displayed on the keypad.
4. Panel Sections [301], [302], [303], and [305] can be configured as Primary communication paths.
a. Panel Sections [302], [303], and [305] may also be configured for backup or redundant communications by using Panel Section(s)
[383] or [351] - [376]. Refer to the SCW panel Installation Manual for more information.
b. If a valid telephone number is programmed, communications will use Public Switched Telephone Network (PSTN). Entering a 4
digit hexadecimal value for a telephone number will change the call routing to the Communicator, as determined by the number
programmed:
DCAAF:Internal (All Receivers). Signals will be routed depending on Section [851] [006] programming.
DCBBF: Ethernet Receiver 1 (Primary). (Not available for 3G2055-SM).
DCCCF:Ethernet Receiver 2 (Backup). (Not available for 3G2055-SM).
DCDDF:Cellular Receiver 1 (Primary). (Not available for TL255-SM-NA).
DCEEF: Cellular Receiver 2 (Backup). (Not available for TL255-SM-NA).
NOTE: Add a single ‘F’ as a suffix to the 4 digit hex number to populate the unused remainder of the 32 character field.
5. Panel Section [350]: If any of the phone numbers have been programmed as DCAA, DCBB, DCCC, DCDD, or DCEE, panel Sec-
tion [350] must be set to [04] if SIA format or [03] if Contact ID (CID) format.
6. Panel Section [382]: Toggle Option [5], ‘GS/IP Module Enabled’, must be set to ON.
7. Panel Section [401]: Toggle Option [1] must be set to ON in order to perform panel DLS session through Cellular or Ethernet.
NOTE: Keep a record of the SIM card telephone number, it is required by users for SMS Command and Control functions. Due to the
nature of the SIM card activation process with 3G network carriers, it can take up to 24 hours for SIM card activation to be
complete.
Fig
ure 1: Layou
t of UA580
DRAFT-02_by_MM