User's Manual

Alarm Communicator Installlation Manual SMS Command and Control Functions
23
The User can send just the partition number or the complete label.(e.g., “Away arm Partition 2 1234” is treated the same as “away arm
2 1234 ”).
The SMS Message format is in 3 parts: Command, Partition Label (or only the partition number), and Access Code.
• If an Access Code is included in the message, it is sent to the control panel for validation, along with the requested function.
• If the panel is configured to require an Access Code and the code is not sent (or invalid) the panel will fail the function (unsuccess-
ful).
• If the panel fails the function, an SMS response message is sent to the user. The SMS response will echo the command sent, followed
by the label “unsuccessful”. (e.g., “night arm partition 2 1234 unsuccessful”).
• The partition label or partition number may be excluded from the SMS request in a single partition system (e.g., disarm 9123).
NOTE: The Cellular phone number can be viewed in Section [996] or by User entering *6 [<] [>] “Cellular Phone No.” at the keypad.
An Access Code is required for all SMS commands, except Help.
[601] Stay Arm
Default (Stay Arm);
Send this command to the system to stay arm. It may be followed by a Partition Label or partition number and Access Code.
[602] Away Arm
Default (Away Arm);
Send this command to the system to away arm. It may be followed by a Partition Label or partition number and Access Code.
[603] Night Arm
Default (Night Arm);
Send this command to the system to night arm. It may be followed by a Partition Label or partition number and Access Code.
[604] Disarm
Default (Disarm);
Send this command to the system to disarm. It may be followed by a Partition Label or partition number and Access Code.
[605] - [608] Activate Command Output 1 - 4
Default (Activate Command Output n);
Where n is a number from 1 - 4. Send this command to the system to activate a command output. It may be followed by a Partition
Label or partition number and Access Code.
[609] - [612] Deactivate Command Output 1 - 4
Default (Deactivate Command Output n);
Where n is a number from 1 - 4. Send this command to the system to deactivate a command output . This command may be followed by
a Partition Label or partition number and optional Access Code.
[613] Bypass
Default (Bypass);
Send this command to the system to bypass a Zone. This command should be followed by a Zone label or Zone number and Access
Code.
[614] Unbypass
Default (Unbypass);
Send this command to the system to unbypass a Zone. This command should be followed by the Zone label or Zone number and Access
Code.
[615] Status Request
Default (Status Request);
Send this command to request the status of the system. It may be followed by a partition label or partition number and Access Code. If
partition label is omitted, status of all enabled partitions will be sent. If there is a trouble on the system, the system label is sent, fol-
lowed by the trouble label, then the partition status.
NOTE: Status Request response may require more than 1 SMS message, depending on status of the system. There is a 10 second delay
between transmission of SMS messages.
[616] Alarm Memory Request
Default (Alarm Memory Request);
Send this command to the system to request the alarm memory from the system. This command may be followed by a Partition Label
or partition number, and Access Code. If partition label is omitted, alarm memory of all partitions will be sent. Alarm memory
responses will include Partition label and Zone label. Up to 8 partitions may be contained in 1 message.
NOTE: Alarm Memory Request response may require more than 1 SMS message, depending on alarm memory of the unit. There is a
10 second delay between transmission of SMS messages.
[617] Help
Default (Help);
When help is sent, the SMS response is a listing of all Interactive commands that can be sent to the module. Access Code is not
required.
[619] Keypad Message
Default (Keypad Message);
The response format is: [Account Label] [Date and Time] [SMS Function] [Response] [Message Text]. Fields are space delim-
ited.When Keypad Message is sent, the SMS response is the message displayed on the keypad. If the message is too long to display on
the keypad, only the portion displayed is sent in the response.
DRAFT-02_by_MM