User's Manual

Event Notification and Interactive Options Alarm Communicator Installlation Manual
20
[226] Cellular Trouble Delay
Default (00);
This option is used to program the delay, in minutes, for reporting a Cellular Trouble Delay. Valid entries are 00 - FF.
(e.g., for a 10 minute Cellular Trouble Delay enter 0A). There is no delay if value is programmed as 00.
[227] Voice Call Timeout
Default (00);
This option sets the Voice Call Timeout, in minutes. Programming a value of 00 will disable timeout. Valid range is 00 to FF.
[228] Voice Call Back Time
Default (0A);
This option sets the Voice call back time, in minutes. When the Communicator requests Call Back from the receiver, it will answer
incoming calls during the programmed timeout period. If an incoming call is received after the timeout from requesting call back, the
Communicator will answer the call and immediately hang up. Programming a value of 00 will disable timeout (accept all incoming
calls). Default value is 0A/10 seconds. Valid range is 00 to FF.
[229] Voice Call Back Number
Default (SIM Telephone Number);
This option sets the Voice Call Back Telephone Number for the receiver. This number is used for Two Way calling. Current SIM tele-
phone number can be viewed in Section [996]. Valid entry is 32 character ASCII.
EVENT NOTIFICATION AND INTERACTIVE OPTIONS
[301] Command and Control Toggle Options
[1] SMS Notification Default (ON).
[2] Reserved Default (OFF).
[3] SMS Command and Control Default (ON).
[4] Interactive Default (ON).
[5] SMS Character Format Default (See Table 12 below for default by language selection).
ON: SMS Unicode, maximum message length is 70 characters.
OFF: 7 bit SMS, maximum message length is 160 characters.
[6] Long SMS Message Handling Default (OFF);
ON: If longer than maximum message length, it is split and sent as multiple SMS messages.
OFF: If longer than maximum message length. A single, truncated SMS message is sent.
[7-8]Reserved Default (OFF).
[311] - [318] SMS Phone Number 1 - 8
Default ( );
These Sections may be programmed through DLS IV or the keypad. Up to 8 SMS telephone numbers (4 - 32 digits) can be programmed
in Section [31x] Where x is an SMS telephone number from 1 to 8. Leaving programming blank for a telephone number will disable
that number. The User can program their own mobile telephone numbers at the keypad using
[*] [6] <> “SMS Programming”. The SMS Command and Control feature utilize the SMS messaging service provided by the Cellular
network and is subject to the limitations of SMS messaging. These limitations include delayed messages and lack of guaranteed deliv-
ery.
NOTE: SMS Command and Control (Sections [601] - [618] will only process messages from the mobile telephone numbers pro-
grammed in this Section if SMS Command and Control is enabled [301][ 3] ON. SMS responses are listed in Sections [621] -
[630]. A blank telephone number is disabled.
SMS NOTIFICATION
[321] - [328] SMS Phone Number 1 - 8 Toggle Options
The toggles in this Section determine the type of event message that will be sent to the SMS number programmed in
Sections [311] - [318].
[1] SMS Notification Alarm/Restore Default (ON).
[2] SMS Notification Tamper/Restore Default (ON).
[3] SMS Notification Opening/Closing Default (ON).
[4] SMS Notification System Maintenance Default (ON).
[5] SMS Notification System Test Default (ON).
[6] SMS Notification Internal Events Default (ON).
[7] SMS Notification Enabled Default (ON).
Table 12: Event Notification Language
Language Default Language Default Language Default Language Default
English OFF Czech ON Greek ON Latvian OFF
Spanish OFF Finnish OFF Turkish OFF Lithuanian OFF
Portuguese OFF German OFF Croatian ON Ukrainian ON
French OFF Swedish OFF Hungarian ON Slovakian OFF
Italian OFF Norwegian OFF Romanian OFF Serbian ON
Dutch OFF Danish OFF Russian ON Estonian OFF
Polish ON Hebrew ON Bulgarian ON Slovenian OFF
DRAFT-02_by_MM