User's Manual

Alarm Communicator Installlation Manual System Options
11
OFF:The Communicator module firmware can not be remotely upgraded. Local firmware upgrade is still possible.
[7] Alternate Test Transmissions Default (OFF).
ON: When the periodic test transmission interval occurs, the test transmission will alternate between being sent to the primary
and secondary receivers with each test transmission interval.
OFF:When the periodic test transmission interval occurs, the test transmission will be sent to the programmed receivers, based
on the settings of the periodic test transmission reporting codes.
[8] Reserved. Default (OFF).
[006] System Toggle Options 2
[1] Ethernet 1 Receiver Enabled. Default (ON) [OFF 3G2055-SM]
.
ON: Ethernet Receiver 1 is enabled.
OFF: Ethernet Receiver 1 is disabled.
[2] Ethernet 2 Receiver Enabled. Default (ON) [OFF 3G2055-SM].
ON: Ethernet Receiver 2 is enabled.
OFF: Ethernet Receiver 2 is disabled.
[3] Reserved. (OFF).
[4] Cellular 1 Receiver Enabled. Default
(ON).
ON: Cellular Receiver 1 is enabled.
OFF: Cellular Receiver 1 is disabled.
[5] Cellular 2 Receiver Enabled. Default
(ON).
ON: Cellular Receiver 2 is enabled.
OFF: Cellular Receiver 2 is disabled.
[6] Reserved (OFF).
[7] DLS Over Cellular. Default (ON). [OFF TL255-SM]
NOTE: Program this toggle as OFF if you want to completely disable DLS from using the Cellular path.
ON: DLS is enabled on the Cellular path.
OFF: DLS is disabled on the Cellular path.
NOTE: If Toggle Option [7] is OFF, DLS sessions will occur on the Ethernet path only, regardless of Primary Path set in Section
[005] Toggle Option [4]. If it is ON then the Communicator will connect to the primary path first for DLS and if the ses-
sion fails, the secondary path will be used.
[8] Reserved. Default (ON).
[007] DNS Server IP 1
Default (000.000.000.000);
 Programming this Section is not permitted on a UL/ULC listed system.
Enter the IP address for DNS Server 1. Format is 4 fields, each field is a 3 digit decimal. Valid range: 000-255.
NOTE: If no value is programmed and DHCP is used, the DHCP Server will configure the address. If an address is programmed and
DHCP is used, the address that you program will be used instead of the DHCP address.
[008] DNS Server IP 2
 Programming this Section is not permitted on a UL/ULC listed system.
Default (000.000.000.000);
Enter the IP address for DNS Server 2. Format is 4 fields, each field is a 3 digit decimal. Valid range: 000-255.
NOTE: If no value is programmed and DHCP is used, the DHCP Server will assign this value. If an address is programmed and DHCP
is used, the address that you program will be used instead of the DHCP address.
[009] Language
Default (01);
NOTE: Immediately after programming this Section, perform a Default Languages in Section [999][11] to have programmable labels
available in the selected language. Programming this Section with an invalid language number will default to English [01].
Connect24 will automatically update all programmable language labels when this Section is changed.
Table 6: Label Languages
OPT Language OPT Language OPT Language OPT Language
00 Reserved 08 Czech 16 Turkish 24 Lithuanian
01 English 09 Finnish 17 Reserved 25 Ukrainian
02 Spanish 10 German 18 Croatian 26 Slovakian
03 Portuguese 11 Swedish 19 Hungarian 27 Serbian
04 French 12 Norwegian 20 Romanian 28 Estonian
05 Italian 13 Danish 21 Russian 29 Slovenian
06 Dutch 14 Hebrew 22 Bulgarian 30-99 Reserved
07 Polish 15 Greek 23 Latvian
DRAFT-02_by_MM