User's Manual

ManualsBrandsDigital Security Controls ManualsElectronicsGSM ALARM COMMUNICATOR FOR DSC POWER SERIES PANELS

[021] Account Code

Default (FFFFFF)

The account code is included when transmitting any events generated by the Communicator. (e.g., Panel Absent

Trouble). It is recommended that the account code be the same as the control panel account number. Valid range:

00000

-FFFFF

. If 4 digit account codes are needed the 2 lowest digits shall be programmed as FF;(e.g., Account

1234 is programmed as:1234

NOTE: Programming this Section with all 0 or F will cause a Module Configuration Trouble (yellow LED=12 flashes).

[022] Communications Format

Default (04)

Program 03 for Contact ID (CID). Program 04 for SIA. The module can be configured to send Communicator

Events in SIA or CID format. The SIA communication format follows the level 2 specifications of the SIA Digital

Communication Standard - October 1997. This format will send the account code along with its data transmission.

The transmission will look similar to the following at the receiver. Example:

Nri0 ET001

Where:

= New Event;

ri0

= Partition/Area identifier;

= Panel Absent Trouble;

001

= Zone 001.

Communications Reporting Codes

[023] Panel Absent Trouble

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur when communications with the panel have

been lost for more than 60 seconds.

[024] Panel Absent Trouble Restore

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur when communications with the control panel

have resumed.

[025] Radio Activation Restore

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur after any successful Connect24 program-

ming session.

System Test Options [026 - 029]

Test Transmissions to Primary Receiver, with Backup to Secondary Receiver:

Set Ethernet Section [026] to (FF); [027] to (00). Set GPRS Section [028] to (FF); [029] to (00).

• If the test transmission fails to the primary receiver it will backup to the secondary receiver.

• If the test transmission fails to the secondary receiver an FTC trouble will be generated.

Test Transmission Unique to Primary and Secondary Receivers:

Set Ethernet Section [026] to (FF); [027] to (FF). Set GPRS Section [028] to (FF); [029] to (FF).

• The module will send periodic test transmissions to each receiver independently, with no backups.

• If the test transmission fails to any of the programmed receivers, an FTC trouble will be generated.

45 +5

CAST Chinese Atlantic Standard Time

70 - FF

Reserved

WKST West Kazakhstan Standard Time

PKT Pakistan Time

YEKT Yekaterinburg Time

UZT Uzbekistan Time

TMT Turkmenistan Time

TJT Tajikistan Time

TFT French Southern and Antarctic Time

MVT Maldives Time

MAWT Mawson Time

KGT Kyrgyzstan Time

HMT Heard and McDonald Island Time

DAVT Davis Time

Table 8: Communications Reporting Codes

Event

SIA

Identifier

SIA

Reporting

Code

CID

Qualifier

CID

Event

Code

CID

Reporting

Code

CID

User/

Zone

[023] Panel Absent Trouble ET 001 1 3 55 001

[024] Panel Absent Trouble Restore ER 001 3 3 55 001

[025] Radio Activation Restore RS 001 3 5 52 001

[026] Ethernet 1 Test Transmission RP 001 1 6 A3 951

[027] Ethernet 2 Test Transmission RP 002 1 6 A3 952

[028] GPRS 1 Test Transmission RP 003 1 6 A3 955

[029] GPRS 2 Test Transmission RP 004 1 6 A3 956

[030] FTC Restore YK 001 3 3 54 001

Table 7: Time Zone Offset (Continued)

HEX

Offset

Hours

Std

Abbrev

Location HEX

Offset

Hours

Std

Abbrev

Location