User's Manual
Table Of Contents
- t6y
- t6y
- RFK5501/5500-433 v1.1
- Installation Instructions, Instrucciones de instalación
- English, Español
- English, Español
- English, Español
- English
- Installation Instructions
- Installation Instructions
- •PC580
- •PC585
- •PC1555MX
- •PC1565
- •PC1616
- •PC1832
- •PC1864
- •PC5005
- •PC5008
- •PC5010
- •PC5015
- •PC5016
- •PC5020
- •PC5020
- •PC5020
- •PC5020
- •One Power keypad
- •Keypad inner door labels
- •Four mounting screws
- •1 tamper switch
- •2 end-of-line resistors
- •Installation Instructions
- 1. Insert a flat head screwdriver into the provided slot (first of two)
- 2. Move screwdriver toward the back plastic and lift as in the below diagram. This will unhook one side of the front plastic.
- 3. Repeat step # 1 and 2 on the second provided slot to disconnect the front plastic and allow access for wiring.
- 2. Place keypad into hooks on the backplate and swing down to engage.
- 3. Run wire through wiring slot or knockouts. Connect Keybus and PGM/Zone wiring to keypad. Place tamper switch into tamper hole on backplate.
- 4. Remove keypad from hooks. Place keypad into backplate, ensure the wire is pushed back into the wall as much as possible. Route the wire inside the keypad ensuring high components are avoided. Snap the front assembly closed, ensuring that there is ...
- 2. Connect the four Keybus wires from the control panel (red, black, yellow and green) to the keypad terminals. Refer to diagram:
- 3. If programmed as an input, you can connect a device - such as a door contact - to the ‘P/Z’ terminal of the keypad. This eliminates the need to run wires back to the control panel for the device. To connect the zone, run one wire from the devi...
- 4. If the ‘P/Z’ terminal is programmed as an output, the output follows the PGM programmed in Section [080]. A small relay, buzzer or other DC operated device may be connected between the positive supply voltage and the ‘P/Z’ terminal (maximu...
- 2. Connect the AC transformer.
- 2. Press [000] for Keypad Programming
- 3. Press [0] for Partition and Slot Assignment
- 4. Enter the 1st digit (0 to 8 for partition assignment)
- 5. Enter the 2nd digit (1 to 8 for slot assignment supervision)
- 6. Press the [#] key twice to exit programming.
- 7. After assigning all keypads, perform a supervisory reset by entering [Q][8][Installer’s Code][902] and wait for 60 seconds.
- 8. Press the [#] key to exit programming after 60 seconds.
- 2. Use the arrow keys (<>) to move the underline bar underneath the letter to be changed.
- 3. Press the number keys [1] to [9] corresponding to the letter you require. The first time you press the number the first letter will appear. Pressing the number key again will display the next letter.
- [1] - A, B, C, 1
- [4] - J, K, L, 4
- [7] - S, T, U, 7
- [0] - Space
- [2] - D, E, F, 2
- [5] - M, N, O, 5
- [8] - V, W, X, 8
- [8] - V, W, X, 8
- [3] - G, H, I, 3
- [6] - P, Q, R, 6
- [9] - Y, Z, 9,0
- [9] - Y, Z, 9,0
- 4. When the required letter or number is displayed use the arrow keys (<>) to scroll to the next letter.
- 5. When you are finished programming the Zone Label, press the [Q] key, scroll to “Save,” then press [Q].
- 6. Continue from Step 2 until all Labels are programmed.
- 2. Use the [<][>] keys to scroll to either Brightness Control or Contrast Control.
- 3. Press [Q] to select the setting you want to adjust.
- 4. a) ‘Brightness Control’: There are multiple backlighting levels. Use the [<][>] keys to scroll to the desired level. b) ‘Contrast Control’: There are 10 different display contrast levels. Use the [<][>] keys to scroll to the desired contra...
- 5. To exit, press [#].
- 2. Use the [>] key to move through the 4 different backlighting levels.
- 3. The level is automatically saved when you press [#] to exit.
- 2. Use the [<][>] keys to scroll to Buzzer Control.
- 3. There are 21 different levels, use the [<][>] keys to scroll to the desired level.
- 4. To exit, press [#].
- 2. Use the [<] key to move through the 21 different buzzer levels.
- 3. The level is automatically saved when you press [#] to exit.
- Partition Assignment (0=Global Keypad)
- Slot Assignment
- 1 to 8
- [1]
- Function Key 1 Assignment
- 00 to 32
- 03
- Stay Arm
- [2]
- Function Key 2 Assignment
- 00 to 32
- 04
- Away Arm
- [3]
- Function Key 3 Assignment
- 00 to 32
- 06
- Chime On/Off
- [4]
- Function Key 4 Assignment
- 00 to 32
- 14
- Sensor Reset
- [5]
- Function Key 5 Assignment
- 00 to 32
- 16
- Quick Exit
- [00] - Null
- [08] - Bypass Mode
- [16] - Quick Exit
- [26] - Time & Date Program
- [01] - Partition 1 Select
- [09] - Trouble Display
- [17] - Activate Stay/Away
- [27] - Partition 3 Select
- [02] - Partition 2 Select
- [10] - Alarm Memory
- [18] - *Global Away Arm
- [28] - Partition 4 Select
- [03] - Stay Arm
- [11] - User Programming
- [19] - Command Output 3
- [29] - Partition 5 Select
- [04] - Away Arm
- [12] - User Functions
- [21] - Command Output 4
- [30] - Partition 6 Select
- [05] - No Entry Arm
- [13] - Command Output 1
- [22] - *Global Disarming
- [31] - Partition 7 Select
- [06] - Chime On/Off
- [14] - Command Output 2
- [23] - Bypass Recall
- [32] - Partition 8 Select
- [07] - System Test
- [15] - *Global Stay Arm
- [24] - Bypass Group Recall
- [33] - Local PGM Activate
- *Available only on the PC1616/PC1832/PC1864 version 4.2 or higher.
- [001] to [064]
- 1 to 64
- [101] to [108]
- 1 to 8
- [00] - Null
- [07] - System Test
- [17] - Activate Stay/Away
- [27] - Disarm
- [03] - Stay Arm
- [13] - Command Output 1
- [18] - Global Away Arm
- [28] - Fire Alarm
- [04] - Away Arm
- [14] - Command Output 2
- [19] - Command Output 3
- [29] - Auxiliary Alarm
- [05] - No Entry Arm
- [15] - Global Stay Arm
- [21] - Command Output 4
- [30] - Panic Alarm
- [06] - Chime On/Off
- [16] - Quick Exit
- [22] - Global Disarm
- [31] - Local PGM Activate
Entre en la programación del teclado pulsando [4][8][Código del instalador][000]
[0] Asignación de partición / ranura
[1]-[5] Asignación de las teclas de función
Teclas de función del teclado
Consulte el manual de instalación del sistema para obtener una lista completa de todas las teclas de función
disponibles para su sistema.
Entre en la programación del teclado pulsando [4][8][Código del instalador][4].
[001]-[064] Etiqueta de la zona 1 a la 64
Ej. Para la zona 1, entre en la sección [001]; para la zona 2, entre en la sección [002], etc.
Predefinida: “Zona 01” - “Zona 64”
[065] Etiqueta de la alarma contra incendios (28 caracteres)
Predefinida:“Zona de Fuego”
[066] Mensaje de evento de fallo en el armado
Predefinida: “Sisteme Falló al Armar”
[067] Mensaje de evento de alarma al armar
Predefinida: “Hubo Alarmas Durante Armado < >”
[071] Máscara visualizada del primer usuario
[072] Máscara visualizada del segundo usuario
Cifra Opción Intervalo válido Predefinido
1ª Partición (0=Teclado global) 0 - 8 1 I_____I
2ª Asignación de ranura 1 - 8 LED,ICONOS=1/LCD=8 I_____I
Tecla de función Botón Intervalo válido Predefinido Función
[1]
Asignación de la
tecla de función 1
00 - 32 03 Armar interior I_____I_____I
[2]
Asignación de la
tecla de función 2
00 - 32 04 Armar exterior I_____I_____I
[3]
Asignación de la
tecla de función 3
00 - 32 06 Timbre On/Off I_____I_____I
[4]
Asignación de la
tecla de función 4
00 - 32 14 Reset de Sensores I_____I_____I
[5]
Asignación de la
tecla de función 5
00 - 32 16 Salida rápida I_____I_____I
[00] - Vacío [11] - Programación del usuario [23] - Memorizar derivación
[01] - Seleccionar partición 1 [12] - Funciones del usuario [24] - Memorizar derivación
[02] - Seleccionar partición 2 [13] - Salida de orden 1 [26] - Programar fecha y hora
[03] - Armar interior [14] - Salida de orden 2 [27] - Seleccionar partición 3
[04] - Armar exterior [15] - Armado presente global* [28] - Seleccionar partición 4
[05] - No armar ninguna entrada [16] - Salida rápida [29] - Seleccionar partición 5
[06] - Timbre On/Off [17] - Activar interior/exterior [30] - Seleccionar partición 6
[07] - Prueba de sistema [18] - Armado ausente global* [31] - Seleccionar partición 7
[08] - Modo de derivación [19] - Salida de orden 3 [32] - Seleccionar partición 8
[09] - Mostrar problema [21] - Salida de orden 4 [33] - Activación PGM Local
[10] - Memoria de alarma [22] - Desarmado global*
*Estas características están disponibles sólo en el PC1616/PC1832/PC1864, la versión 4,2 o más alto solo.
Sección Zona Etiqueta
[001] - [064] 1 - 64
I_____I___ __I_____I__ ___I_____I__ ___I_____I____ _I_____I____ _I_____I___ __I_____I___ __I
I_____I___ __I_____I__ ___I_____I__ ___I_____I____ _I_____I____ _I_____I___ __I_____I___ __I
[065]
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[066]
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[067]
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Predefinido Opc ON OFF
ON I____I 1 Indicador de Mantener tecla de pánico [P] ON
Indicador de Mantener tecla de pánico [P] OFF
ON I____I 2
Indicador de Control/Tiempo de armado
automático ON
Indicador de Control/Tiempo de armado
automático OFF
ON I____I 3 Indicador de Armado rápido ON
Indicador de Armado rápido OFF
ON I____I 4 Indicador de Armado interior ON
Indicador de Armado interior OFF
OFF I____I 5 Indicador de Salida rápida ON
Indicador de Salida rápida OFF
OFF I____I 6 Indicador de Control del termostato ON
Indicador de Control del termostato OFF
OFF I____I 7 Indicador de Reconocer todos problemas ON Indicador de Reconocer todos problemas
OFF
OFF I____I 8 Indicador de Entrada de música ON
Indicador de Entrada de música OFF
Predefinido Opc ON OFF
ON I____I 1
Indicador de llamada iniciada por el
usuario ON
Indicador de llamada iniciada por el usuario OFF
OFF I____I 2 Para uso futuro
OFF I____I 3
Indicador de Comprobación por una sola
persona ON
Indicador de Comprobación por una sola persona
OFF
ON I____I 4 Indicador de salida de orden 1 ON Indicador de salida de orden 1 OFF
ON I____I 5 Indicador de salida de orden 2 ON Indicador de salida de orden 2 OFF
OFF I____I 6 Indicador de salida de orden 3 ON Indicador de salida de orden 3 OFF
OFF I____I 7 Indicador de salida de orden 4 ON Indicador de salida de orden 4 OFF
OFF I____I 8 Para uso futuro