User's Manual
Table Of Contents
- TL260GS / TL265GS
- TL260GS / TL265GS
- Installation Manual
- Limited Warranty
- WARNING
- Note to Installers
- System Failures
- Criminal Knowledge
- Access by Intruders
- Power Failure
- Failure of Replaceable Batteries
- Compromise of Radio Frequency (Wireless) Devices
- Smoke Detectors
- Motion Detectors
- Warning Devices
- Telephone Lines
- Insufficient Time
- Component Failure
- Inadequate Testing
- Security and Insurance
- Warning
- FCC
- Introduction
- 1 . On your hard drive, locate the laptop’s IP address. Retrieve the number of the listening port; this is assigned by the application. You should also have on hand the Communicator’s phone number.
- 2 . Using this phone number send the Communicator an 18-digit SMS text message. This SMS text message is to be configured as: ! + IP address + Port number, without stops or spaces (e.g. !11122233344412345). Note that if you intend to use a port numbe...
- 3 . With an existing installation of DLS IV downloading software on your laptop, you now have the ability to program the Communicator using the GUI on the screen. See Options on page 23 for detailed programming information. Also, please refer to your...
- Models
- Features
- Technical Specifications
- Ratings
- Compatibility
- Table 2: Compatible Receivers and Control Panels
- INSTALLING THE GSM / ETHERNET COMMUNICATOR
- 1 . Wire the telephone line, if available.
- 2 . Wire the PC9155 panel (but not the Communicator).
- 3 . Turn on the PC9155 panel. Program the panel’s telephone number, account code, format, GS / IP module enable, and the communication path priority (i.e. PSTN > Ethernet > GRPS).
- 4 . Turn off the panel.
- 5 . Wire the Communicator through the PC-Link.
- 6 . Proceed to CONNECT 24 Activation Information below.
- 7 . Turn on the panel. Wait for the initialization of the Communicator.
- 1 . Assemble the Communicator
- 2 . Install the Communicator module into the Cabinet
- 3 . Turn on the panel and check signal strength.
- 1 . Attach the Communicator to the inside of the PC9155 control panel cabinet if not already present.
- 2 . Turn on the PC9155 cabinet and check signal strength.
- 1 . Program the hexadecimal digits (DCAA) in the telephone number that will be used to contact the GSM / Ethernet Communicator (panel Options 301, 302, 303, ‘Telephone Phone Number Programming’).
- 2 . In Option 350, program the communication format as SIA FSK.
- 3 . In Options 351 through Option 376, program the call direction sub-options for the phone number being used to communicate using the GSM / Ethernet Communicator.
- 4 . Option 382, sub-option 5 must be set to ON.
- STATUS LEDs
- Trouble Status LED
- Network Connection Status LED
- Signal Strength LEDs
- Table 4: Radio Signal Strength
- 1 . Turn off the power to the Communicator by physically unplugging the unit from its power supply.
- 2 . Attach one end of the extension cable to the Communicator and the other end to the antenna itself.
- 3 . Reattach the power supply and turn on.
- 4 . Move the antenna around until you have received a strong signal.
- 5 . Mount the antenna bracket at that location.
- 1 . Locate the set of five vertically aligned pins in the middle of the Communicator board.
- 2 . Counting from the bottom, the first three pins are reserved for future use. You may discount these.
- 3 . The final two pins require a jumper in order to reset the hardware values.
- 4 . Turn off power to the Communicator.
- 5 . Apply the jumper to the two pins.
- 6 . Turn on power to the Communicator. Wait for ten seconds.
- 7 . Remove the jumper from the pins.
- Table 5: Communicator Troubles on a 9155 Panel
- Table 4: Radio Signal Strength
- Options
- Programming Worksheets
21
5. Apply the jumper to the two pins.
6. Turn on power to the Communicator. Wait for ten seconds.
7. Remove the jumper from the pins.
The hardware settings of your Communicator have now been reset to their default values.
Communicator Troubles on a 9155 Panel
The following troubles will appear on the keypad LCD when encountered by a Communicator on the 9155 panel.
Table 5: Communicator Troubles on a 9155 Panel
Trouble Condition Description User Action
Alternate Communicator
Trouble
Inidcates AC failure, Low battery, Sim card lock,
GSM trouble, Ethernet trouble, Central station
receiver trouble, supervision config SMS trouble for
GS/IP module (if installed). Press <> to scroll through
troubles.
Call for service. For Ethernet trou-
ble check LAN connections.
Service Required (Press 1
for more information)
Inidcates Low battery, System trouble, system tamper
or RF jam detected.
Call for service.
Loss of AC Power If the building or neighbourhood has lost electrical
power, the system will continue to operate on battery
for several hours.
Call for service. Check AC connec-
tion.
Telephone Line Fault The system has discovered that a telephone line is dis-
connected.
Call for service.
Failure to Communicate The system has attempted to communicate with the
monitoring station, but failed. This may be due to a
telephone line fault.
Call for service.
Module/Sensor Fault The system is experiencing difficulties with one or
more modules or sensors on the system.Continue to
press 5 to navigate through the Zone, Keypad, and
Siren fault menus.
Call for service.
Module/Sensor Tamper The system has detected a Tamper condition with one
or modules or sensors on the system. Continue to press
6 to navigate through the Zone, Keypad, and Siren
tamper menus.
Call for service.
Module/Sensor Low Battery The system has detected a Low Battery condition with
one or modules or sensors on the system. Continue to
press 7 to display the Zone(s), Wireless key(s), Key-
pad(s), and Proximity tag(s).
Call for service.
AUDIO/DEFAULT
DSC
UA557
PC-LINK
DG009054