User's Manual

ManualsBrandsDigital Security Controls ManualsElectronicsASK Receiver

PK55XX

RFK55XX-433

W A RNING: Please refer to the System Installation Man-

ual for information on limitations regarding product use and

function and information on the limitations as to liability of the

manufacturer.

NOTE: These instructions shall be used in conjunction with

the system Installation Manual of the Control Panel with which

this equipment is intended to be used.

Installation Instructions

The PK55XX\RFK55XX keypads can be used on security systems with

up to 64 zones. These keypads are compatible with the following

DSC security systems:

The RFK55XX keypads combine a standard PC5132 receiver with the

respective PK55XX keypad.

Specifications

• Voltage rating: 12V

DC nominal

• Connects to control panel via 4-wire Keybus

• 1 keypad zone input/PGM output*

• Current draw: 50mA (standby) /125mA (maximum)

• Optional tamper version

• 5 programmable function keys

• Ready (green LED), Armed (red LED), Trouble (yellow LED), AC

(green LED)

• Low temperature sensor

• Frequency: 433.92MHz

(RFK55XX-433 Only)

• Upto 32 wireless zones (RFK55XX Only)

NOTE: * Zone not to be programmed as Fire type or 24h type.

Unpacking

The Power keypad package includes the following parts:

• One Power keypad • Keypad inner door labels

• Four mounting screws • 1 tamper switch

• 2 end-of-line resistors • 1 Installation Instructions

Mounting

You should mount the keypad where it is accessible to designated

points of entry and exit. Once you have selected a dry and secure

location, perform the following steps to mount the keypad.

1. Removing the keypad from the backplate for the first time.

(a) Position the keypad as indicated below, insert screwdriver and

rotate.

2. Removing the keypad from backplate once mounted.

(a) Open door, holding it 90° to the keypad, as shown below.

(b) Insert screwdriver into slot located under the door hinge and

rotate the screwdriver.

Wiring

1.Before wiring the unit, ensure that all power (AC transformer and

battery) is disconnected from the control panel.

2.Connect the four Keybus wires from the control panel (red, black,

yellow and green) to the keypad terminals. Refer to diagram:

3.If programmed as an input, you can connect a device - such as a

door contact - to the ‘P/Z’ terminal of the keypad. This eliminates

the need to run wires back to the control panel for the device. To

connect the zone, run one wire from the device to the ‘P/Z’ terminal

and the other wire from the device to the B (black) terminal. For

powered devices, run the red wire to the R (positive) terminal and

the black wire to the B (negative) terminal. When using end of line

supervision, connect the zone according to one of the configurations

outlined in your system’s Installation Manual.

4.If the ‘P/Z’ terminal is programmed as an output, the output fol-

lows the PGM programmed in Section [080]. A small relay, buzzer

or other DC operated device may be connected between the positive

supply voltage and the ‘P/Z’ terminal (maximum load is 50mA).

Applying Power

Once all wiring is complete, apply power to the control panel:

1. Connect the battery leads to the battery.

2. Connect the AC transformer.

For more information on control panel power specifications, see the

control panel Installation Manual.

Programming the Keypad

There are several programming options available for the keypad.

These are described below. Programming the keypad is similar to

programming the rest of the system. When you are in the keypad

programming sections, the keypad will display which options are

turned on along the top of the display. To turn an option on or off,

press the number correspond-

ing to the option on the num-

ber pad. The numbers of the

options that are currently

turned ON will be displayed.

For example, if options 1 and

4 are on, the display will look

like this on the different key-

pad displays:

For information on program-

ming the rest of your security

system, please refer to your system’s Installation Manual.

Programming LCD Labels

All LCD programming is done per keypad. If more than one LCD key-

pad is present on the system, labels programmed at one keypad can

be broadcast to all other LCD keypads. Perform the following proce-

dure in order to broadcast labels:

Step 1 - Program one LCD keypad completely.

Step 2 - Make sure all LCD keypads are connected to the Keybus.

Step 3 - Enter Installer’s Programming, then enter section [998] at

the keypad that was programmed. The keypad will now broadcast

all the information programmed to all the other LCD keypads on the

system.

Step 4 - When the keypad is finished press the [#] key to exit.

NOTE: Label brodcast from this keypad is only compatible with other

PK5500 and RFK5500 Keypads.

Installation Instructions

123

456

RFK5500

PK5500

123

456

RFK5501

PK5501

123

456

RFK5508

PK5508

123

456

RFK5516

PK5516

•PC580/PC585 •PC1555MX/PC1565 •PC1616/PC1832/PC1864

•PC5005 •PC5008 •PC5010

•PC5015 •PC5016 •PC5020

Disasembling

(Free-standing)

1. Insert the screwdriver into

slot at an angle and push

3. Repeat steps

1. and 2. for

left side

2. Rotate 90°

3. Repeat steps 1.

and 2. for right sid

Disasembling

(Wall-Mounted)

1. Insert the screwdriver into

slot at an angle and push

2. Rotate 90°

PK55XX\RFK55XX

RED

BLK

YEL

GRN

To zone or

PGM out

P/Z

FCC Compliance Statement

Caution: Changes or modifications not expressly approved by Digital

Security Controls could void your authority to use this equipment.

This equipment generates and uses radio frequency energy and if not installed

and used properly, in strict accordance with the manufacturer’s instructions,

may cause interference to radio and television reception. It has been type tested

and found to comply with the limits for Class B device in accordance with the

specifications in Subpart “B” of Part 15 of FCC Rules, which are designed to

provide reasonable protection against such interference in any residential

installation. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause interference to television or

radio reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

• Re-orient the receiving antenna

• Relocate the alarm control with respect to the receiver

• Move the alarm control away from the receiver

• Connect the alarm control into a different outlet so that alarm control and receiver

are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/televi-

sion technician for additional suggestions. The user may find the following

booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/

Television Interference Problems”. This booklet is available from the U.S.

Government Printing Office, Washington, D.C. 20402, Stock # 004-000-

00345-4.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

IC:160A-RFK55XX4

The term IC before the radio certification number signifies that the Industry

Canada technical specifications were met.

Operating Instructions shall be made available to the user.

Tech. Support: 1-800-387-3630 (Canada, US), 905-760-3036

Printed in Canada

29007261R001

Toggle Options

1 _ _ 4 _ _ _ _

Language Programming (PK5500\RFK5500 Only)

Hold (<>) keys for 2 seconds to enter language programming,

scroll to the desired language and Press [*] to select.

Enrolling the Keypad

The keypad will need to be assigned to a partition and slot if supervi-

sion or keypad zones are being used. Keypad assignments and key-

pad option programming must be done at each keypad individually.

The 1st digit of keypad assignment is used to determine partition

assignment (1 to 8). If partitioning is not used, enter [1]. For Global

Keypads, enter [0].

NOTE: LED and ICON keypads cannot be programmed as Global

Keypads

The 2nd digit of keypad assignment is used to determine slot assign-

ment for keypad supervision. Each keypad will be assigned a differ-

ent slot number from 1 to 8. PK5500 and RFK 5500 LCD keypads

come defaulted in slot 8. If LCD keypads are used one LCD keypad

must remain in slot 8.

NOTE: The RFK55XX enrolls as two modules:

1 = keypad section of the RFK55XX

17 = receiver section of the RFK55XX

NOTE: Deleting all wireless devices from the RFK55XX or

defaulting the RFK55XX will cause a supervisory fault.

Enter the following at each keypad installed on the system:

1. Enter Installer Programming by pressing [*][8][Installer’s Code]

2. Press [000] for Keypad Programming

3. Press [0] for Partition and Slot Assignment

4. Enter the 1st digit (0 to 8 for partition assignment)

5. Enter the 2nd digit (1 to 8 for slot assignment supervision)

6.Press the [#] key twice to exit programming.

7.After assigning all keypads, perform a supervisory reset by entering

[*][8][Installer’s Code][902] and wait for 60 seconds.

8.Press the [#] key to exit programming after 60 seconds.

Keypad Enrollment

Enter keypad programming by pressing [*][8][Installer’s Code][000].

[0] Partition / Slot Assignment

[1]-[5] Function Key Assignment

Keypad Function Keys

Please see your system installation manual for a complete list of all the

function key options available for your system.

Programming Labels (PK5500\RFK5500 Only)

1.Enter Installer’s Programming. Enter the 3-digit section number for the label

to be programmed.

2.Use the arrow keys (<>) to move the underline bar underneath the letter

to be changed.

3.Press the number keys [1] to [9] corresponding to the letter you require. The

first time you press the number the first letter will appear. Pressing the

number key again will display the next letter.

Refer to the following chart:

4.When the required letter or number is displayed use the arrow keys (<>)

to scroll to the next letter.

5.When you are finished programming the Zone Label, press the [*] key, scroll

to “Save,” then press [*].

6.Continue from Step 2 until all Labels are programmed.

NOTE: Label Programming can also be accessed from the [*][6] User

Functions Menu

ASCII Characters

Keypad Programming

Enter keypad programming by pressing [*][8][Installer Code][*]

[001]-[064] Zone Label 1 to 64 (PK5500\RFK5500 Only)

ex. For Zone 1 enter section [001], for Zone 2 enter section [002] etc.

Default: “Zone 1” - “Zone 64

”

[065] Fire Alarm Label (28 Characters) (PK5500\RFK5500 Only)

Default:“Fire Zone”

[066] Fail to Arm Event Message (PK5500\RFK5500 Only)

Default: “System Has Failed to Arm”

[067] Alarm When Armed Event Message (PK5500\RFK5500 Only)

Default: “Alarm Occurred While Armed < >”

[071] First User Display Mask

[072] Second User Display Mask

[073] Download LCD Message Duration

(PK5500\RFK5500 Only)

Default: 003 I_____I_____I_____I (Valid entries are 000-255), 000=Unlimited Message Disp.

This number represents the number of times the Downloaded message is

cleared by pressing any key while the message is up after timeout).

[074] Key Options

[076] First Keypad Options

[077] Second Keypad Options

[080] PGM Terminal 1

D e f a ult: 01 I_______I _______I P G M Outpu t Numb er

[101]-[108] Partition Labels (PK5500\RFK5500 Only)

ex. For Partition 1 enter section [101], for Partition 2 enter section [102] etc.

NOTE: Partition 1 Label is also used as the System Label

[120]-[151] Command Output Labels (PK5500\RFK5500 Only)

Default: “Command_O/P_1” - “Command_O/P_4”

For Partition 1 Command O/P 1 to 4 enter [120] to [123]

For Partition 2 Command O/P 1 to 4 enter [124] to [127]

For Partition 3 Command O/P 1 to 4 enter [128] to [131]

For Partition 4 Command O/P 1 to 4 enter [132] to [135]

For Partition 5 Command O/P 1 to 4 enter [136] to [139]

For Partition 6 Command O/P 1 to 4 enter [140] to [143]

For Partition 7 Command O/P 1 to 4 enter [144] to [147]

For Partition 8 Command O/P 1 to 4 enter [148] to [151]

[201]-[264] Door Chime Sound Programming

You can program the keypad to make upto four different door chime sounds

for individual zones.

ex. For Zone 1 enter section [201], for Zone 2 enter section [202] etc.

[995] Reset Keypad Options to Factory Default

[996] Label Default

(PK5500\RFK5500 Only)

[997] View Software Version (PK5500\RFK5500 Only)

[998] Initiate Global Label Broadcast (PK5500\RFK5500 Only)

[999] Reset Keypad EEPROM to Factory Defaults

Digit Option Valid Range Default

1st Partition Assignment (0=Global Keypad) 0 to 8 1 I_____I

2nd Slot Assignment 1 to 8

LED\ICON=1

LCD=8

I_____I

Function Key

Button

Valid Range Default Function

[1]

Function Key 1

Assignment

00 to 32 03 Stay Arm

I_____I_____II

[2]

Function Key 2

Assignment

00 to 32 04 Away Arm

I_____I_____II

[3]

Function Key 3

Assignment

00 to 32 06 Chime On/Off

I_____I_____II

[4]

Function Key 4

Assignment

00 to 32 14

Command

Output 2

I_____I_____II

[5]

Function Key 5

Assignment

00 to 32 16 Quick Exit

I_____I_____II

[00] - Null [10] - Alarm Memory [23] - Bypass Recall

[01] - Partition 1 Select [11] - User Programming [24] - Bypass Group Recall

[02] - Partition 2 Select [12] - User Functions [26] - Time & Date Program

[03] - Stay Arm [13] - Command Output 1 [27] - Partition 3 Select

[04] - Away Arm [14] - Command Output 2 [28] - Partition 4 Select

[05] - No Entry Arm [16] - Quick Exit [29] - Partition 5 Select

[06] - Chime On/Off [17] - Activate Stay/Away [30] - Partition 6 Select

[07] - System Test [19] - Command Output 3 [31] - Partition 7 Select

[08] - Bypass Mode [21] - Command Output 4 [32] - Partition 8 Select

[09] - Trouble Display [22] - Activate Camera

[1] - A, B, C, 1 [5] - M, N, O, 5 [9] - Y, Z, 9,0

[2] - D, E, F, 2 [6] - P, Q, R, 6 [0] - Space

[3] - G, H, I, 3 [7] - S, T, U, 7

[4] - J, K, L, 4 [8] - V, W, X, 8

Section Zone Label

[001] to [064] 1 to 64

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[065]

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[066]

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[067]

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

Default Option ON OFF

ON I_____I 1 Hold [P]anic Key prompt ON Hold [P]anic Key prompt OFF

ON I_____I 2 Auto-arm Control/Time prompt ON Auto-arm Control/Time prompt OFF

ON I_____I 3 Quick Arm prompt ON Quick Arm prompt OFF

O N I_____I 4 In te rior Arm pro mpt ON I n t erio r Arm pro mpt O FF

OFF I_____I 5 Quick Exit prompt ON Quick Exit prompt OFF

OFF I_____I 6 Thermostat Control prompt ON Thermostat Control prompt OFF

OFF I_____I 7 ACK All Trouble Prompt ON ACK All Trouble Prompt OFF

OFF I_____I 8 Music Input prompt ON Music Input prompt OFF

Default Option ON OFF

O N I_____I 1 U s er-i nit iate d C all- up prom pt ON User-initiated Call-up prompt OFF

O F F I_____I 2 For Futu r e U se

OFF I_____I 3 Walk Test prompt ON Walk Test prompt OFF

ON I_____I 4 Command Output#1 prompt ON Command Output#1 prompt OFF

ON I_____I 5 Command Output#2 prompt ON Command Output#2 prompt OFF

OFF I_____I 6 Command Output#3 prompt ON Command Output#3 prompt OFF

OFF I_____I 7 Command Output#4 prompt ON Command Output#4 prompt OFF

O F F I_____I 8 For Futu r e U se

Default Option ON OFF

O N I_____I 1

[F]ire Key Enabled [F]ire Key Disabled

O N I_____I 2

[A]uxiliary Key Enabled [A]uxiliary Key Disabled

O N I_____I 3 [P]anic Key Enabled [P]anic Key Disabled

O F F I_____I 4 - 8

For Future Use

Default Opt. ON OFF

O N I_____I 1 Disp la y Co de whe n Pr og ra mming Display “Xs” when Programming

O N I_____I 2 L o c a l C l o c k D i s pla y O N L oca l C loc k D isp la y OF F

O F F I_____I 3 L o c a l C l o c k D is p l a y s 2 4 - h r T i me L o c a l Cl oc k D i s p l a y s AM/PM

ON I_____I 4 Auto Alarm Memory Scroll Enabled Auto Alarm Memory Scroll Disabled

OFF I_____I 5 Local Display of Temperature ON Local Display of Temperature OFF

ON I_____I 6 Bypass Options prompt ON Bypass Options prompt OFF

O F F I_____I 7 F o r F u t u r e U s e

OFF I_____I 8 Auto-Scroll Open Zones ON Auto-Scroll Open Zones OFF

Default Opt. ON OFF

ON I_____I 1 Chime Enabled for Zone Openings Chime Disabled for Zone Openings

ON I_____I 2 Chime Enabled for Zone Closings Chime Disabled for Zone Closings

OFF I_____I 3 5th Terminal is Keypad PGM Output 5th Terminal is Keypad Zone Input

O F F I_____I 4 Fo r Fut u r e U s e

OFF I_____I 5 Power LED Enabled Power LED Disabled

O N I_____I 6 Power LED ind icates AC present Power LED indicates AC absent

ON I_____I 7 Alarms always Displayed When Armed Alarms not Displayed When Armed

OFF I_____I 8 Low Temperature Warning Enabled Low Temperature Warning Disabled

Section Partition Label

[101] to [108] 1 to 8

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

Section Part.

Cmd.

Output

Label

[120] to [151] 1 to 8 1 to 4

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

Default Option ON OFF

ON I_____I 1 6 Beeps Disabled

OFF I_____I 2 “Bing-Bing” Sound Disabled

OFF I_____I 3 “Ding-Dong” Sound Disabled

OFF I_____I 4 Alarm Tone Disabled

OFF I_____I 5-8 For Future Use

Summary of content (2 pages)

PAGE 1
Installation Instructions PK55XX RFK55XX-433 Installation Instructions The PK55XX\RFK55XX keypads can be used on security systems with up to 64 zones. These keypads are compatible with the following DSC security systems: •PC580/PC585 •PC1555MX/PC1565 •PC1616/PC1832/PC1864 •PC5005 •PC5008 •PC5010 •PC5015 •PC5016 •PC5020 1. Removing the keypad from the backplate for the first time. (a) Position the keypad as indicated below, insert screwdriver and rotate. Disasembling (Free-standing) Wiring 1.
PAGE 2
Wireless Integration (RFK55XX Only) Compatible Wireless Devices (RFK55XX-433 Only) The RFK55XX can receive signals from the following devices: •WLS904(P)L-433 Pet Immune PIR •WLS912L-433 Glass Break Detector •WS4965 •WLS914-433 Pet Immune PIR •WS4938 Panic Button •WLS925L-433 Mini Door/Window Contact •WS4916 Smoke Detector •WS49X9 Wireless Keys Testing Portable Device Reception [41]-[56] Wireless Key Serial Number To test portable devices (e.g.