Installation Manual
Table Of Contents
- Table of Contents
- Introduction
- 1.1 How to use this Manual
- 1.2 Specifications and Features
- 1.3 Compatible Wireless Devices
- 1.4 Batteries
- PC5132 Set up & Wiring
- 2.1 Unpack the PC5132
- 2.2 Choose a Mounting Location for the PC5132
- 2.3 Antennas
- 2.4 Connect the PC5132 Receiver
- 3.1 A Note about Electronic Serial Numbers
- 3.2 Enrolling Wireless Devices (WLS904NB433, WLS907NB433)
- 3.3 Enroll & Program Wireless Keys (WLS909NB433) 5
- 3.4 Identified Wireless Keys
- Other Programming
- 4.1 Program Zones and Partitions
- 4.2 Enable PC5132 Supervision
- 4.3 Enable Supervision of Wireless Zones
- 4.4 Jamming Signal Detection
- 4.5 PC5132 Software Default
- 4.6 Deleting Wireless Devices
- Testing & Mounting
- 5.1 Test the Reception of Wireless Devices
- 5.2 Mount the PC5132 and Wireless Devices
- Additional Notes
- 6.1 Trouble Conditions
- 6.2 Jamming Signal Detection
- 6.3 Wireless Zone Low Battery Transmission
- Troubleshooting
- Programming Worksheets
- Index
6
4. For each of the 4 function buttons, enter the 2-digit number of the
function you want to select. See the programming worksheets for a list of
function key options.
5. Record your programming choices in the worksheets in the back of the
manual.
6. To exit press [#].
3.4 Identified Wireless Keys
Reporting by the system of openings/closings by individual wireless keys and
command output [✱][7] activation by wireless key buttons may be supported on
certain control panels. To do this, the system will reserve access codes 17 – 32
for wireless keys 01-16 respectively. You must program one access code for
each wireless key (using [✱][5] access code programming) for this feature to
work correctly.
NOTE: Program these access codes on the system
after
you have connected
the PC5132 to the Keybus (see section 2.4).
Refer to your system Installation Manual for information on access code
programming.
Opening/Closing By Wireless Key Reporting
NOTE: The Identified Wireless Key Closing option is only available with the
PC501X, PC5008, PC1565, PC585 v2.0 and higher by turning section [015] option
4 off.
To enable the reporting of openings and closings
by identified wireless keys:
• Make sure the control panel is v2.0 or higher
• Program a valid access code for each key
• Program a closing and opening reporting code for each key’s access
code
• Turn off the Quick Arm option in section [015] option [4] of the control
panel programming
To ensure that an
unidentified wireless key
cannot disarm the system, turn off
section [017], option [1] (in the control panel programming). This option is
available in control panels with software version 2.1 or higher.
Command Output Activation
NOTE: The Identified Wireless Key Command Output Activation feature is only
available with the PC5010, PC5015, PC5008, PC1565 and PC585 v2.0 and higher.
To enable command output activation by wireless keys, ensure that:
• Make sure the control panel is v2.0 or higher
• Program a valid access code for each key
• Enable the PGM output attribute Requires Access Code for each PGM
output programmed as [✱][7][1-4] in sections [141] to [154].
Now that you have enrolled all the wireless devices, you will need to program
the system to work properly with the devices. See section 4 for more information.
W I R E L E S S D E V I C E S