Programming instructions

Digital Monitoring Products XR500 Series Programming Guide
20
remoTe oPTionS
7.7
SVC RCVR NO YES
Service Receiver Authorization
YES enables remote commands and programming to be accepted from a secondary
servicereceiverotherthanthealarmSCS-1RReceiver.TheRemoteKeyoptioncan
also be required.
WithYESselected,thepanelrequeststheservicereceiverkeythersttimeitis
contacted by the service receiver. The panel retains this service receiver key in
memory and accepts remote commands from the service receiver.
If an alarm occurs during a remote connect, the panel disconnects from the service
receiver and calls the alarm receiver. Alarm reports are only sent to the alarm
receiver. It is important that the alarm receiver key and the service receiver key
programmedatthecentralstationareNOTthesamesothepanelcandeterminethe
difference between receivers.
WhenNOisselectedremotecommandsandprogrammingarenotacceptedfroma
secondary service receiver.
This option must be YES to allow programming from a directly connected computer
oraniCOM/iCOM-E.
7.8
PC MODEM NO YES
PC Modem
YESallowsthepaneltoanswerthetelcolinkandconnectwithRemoteLinkthrough
thePCModemat2400baud.NOdisablesPCModemcommunication.
7.9 Send Local Changes
This option allows the panel to automatically update a remote programming
computer at the central station with any changes made to the panel.
Select NET or DD to send local programming changes or User Menu changes to user
codes,userproles,schedules,orholidaydatestoRemoteLinkafterexitingthe
programming or User Menu. If NET is selected, changes are sent using Network. If
DDisselected,changesaresentusingDialer.DefaultisNOtodisablethisfeature.
7.10
REMOTE CHANGE IP
Remote Change IP
ThisoptiondisplayswhenNETisselectedforSendLocalChanges.EntertheIP
address containing up to 12 digits. The Net IP Address must be unique and cannot
be duplicated on the network. Enter all 12 digits and leave out the periods. For
example,enterIPaddress192.168.0.250as192168000250.Theperiodsdisplay
automatically. Default is 000.000.000.000
7.11
REMOTE CHANGE
Remote Change Port
ThisoptiondisplayswhenNETisselectedforSendLocalChanges.EnterthePort
number.Validnumbersarefrom0to65535.Defaultis2002.
7.12 Remote Telephone Number
ThisoptiondisplayswhenDDisselectedforSendLocalChanges.PressCOMMANDto
enter the phone number the panel dials when sending programming changes. After
enteringaphonenumber,thepanelsendsanypanelchangestoRemoteLink.
Thephonenumbercanhavetwolinesof16characterseachtoequal32.Entera
P to program a two second pause in the dialing sequence. The P character counts
aspartofthe32allowablecharacters.Enter*70Pasthestringrstcharactersto
cancel call waiting. Dial tone detect is an automatic panel function.
7.13
DISARM NO YES
Remote Disarm
YESallowsthepaneltobedisarmedremotely.NOdisablesremotedisarming.
7.14 First GPRS APN
EntertherstAPN(AccessPointName).Thisallowsanaccesspointforcellular
communication and is used to connect to a DNS network. The APN may contain two
linesof16characterstoequal32characters.DefaultissettoSECURECOM400.
Second GPRS APN
EnterthesecondAPN(AccessPointName).Thisworksasabackupincasetherst
APNfails.TheAPNmaycontaintwolinesof16characterstoequal32character
DefaultissettoSECURECOM400.
PORT 2002
CHANGES? NO
NO NET DD
SEND LOCAL
000.000.000.000
REMOTE PHONE NO.
-
-
SECURECOM400
-
FIRST GPRS APN
SECURECOM400
-
SECOND GPRS APN