User`s guide

14 XR150/XR350/XR550 User’s Guide Arming and Disarming
Regardless of which conguration is programmed, much of the
operation is similar. Throughout this guide, any differences
between the systems are noted for your convenience.
Arming Functions
Arming or Disarming: You can arm and disarm all areas at one
time or each area individually. You can only arm or disarm areas
authorizedforyourusercode.
Arm All or Selective Arming: After entering your user code, the
system allows you to arm either all of the areas to which you have
access or one or more selected areas. If you choose to arm all
areas, the system begins verifying that all zones in those areas
are in a good condition. If you choose to arm selected areas, the
system prompts you to choose the areas you want to arm.
Aftermakingyourarmingselection,thekeypaddisplaysanyzones
that are currently bypassed. These zones remain bypassed until
the system is armed and then disarmed.Any 24-hour zones in a
faulted condition also display.
Bypassing Zones: Beforearming,thesystemveriesthatalldoors,
win dows, and other protection devices to be armed are in normal
condition.Ifeverythingisveried,thesystemarms.Ifthereisa
problem on one or more burglary zones, the system cannot arm
until the problem is corrected. If the problem is simply an open
door or window, correct the problem and try arming again.
If the problem cannot be corrected, you can force arm or bypass
the zone or wait until the zone can be repaired by a service
technician. A force armed zone is ignored by the system until
it restores to normal.A bypassed zone is ignored by the system
duringtheentirearmedperiod.Azoneremainsbypasseduntilthe
system is disarmed.
Insome cases, youmightseethekeypad display FRONTDOOR —
FAULT.Thekeypadthendisplayspriorityzonewhichisazonethat
cannotbebypassed.Theproblemonthezonemustbecorrected
before the system can be armed.
Whenchoosingtobypassaprotectiondeviceorzone,theremay
be a pre-programmed maximum number of zones (up to 8) that
can be bypassed in an area when that area is being armed. This
limit is programmed at installation.
Arming Messages:
For Area systems the keypad briey displays SYSTEM ON if only
selectedareasarearmed.ThekeypadbrieydisplaysALLSYSTEM
ONwhenallareasinthesystemarearmed.
For All/Perimetersystemsthe keypad briey displaysPERIMETER
ONifonlyselectedareasarearming.Thekeypadbrieydisplays
ALLSYSTEMONwhenallareasinthesystemarearmed.
For Home/Sleep/AwaysystemsthekeypaddisplaysHOMESYSTEMON
or SLEEP SYSTEM ON if only selected areas are arming. The keypad
brieydisplaysALLSYSTEMONwhenallareasinthesystemarearmed.
For Home/Sleep/Away with Guest systems the main system arms
the same as a Home/Sleep/Away system. A keypad assigned to the
rstguesthousesystemdisplaysHOMEGUEST1ONorSLEEPGUEST1
ONifonlyselectedareasarearming.ThekeypaddisplaysALLGUEST
1ONwhenallareasintheguesthousesystemarearmed.
Exit Delay: The keypad then displays the exit delay time as it counts
down. Your system may be pre-programmed at installation to beep
the exit delay tone at eight-second intervals until the last 10 seconds
when the keypad beeps at three-second intervals. After exiting the
building, if you re-enter during the countdown the exit countdown
restarts, allowing additional time to then disarm or again exit the
building during the countdown. This restart can occur only one time.
Whentheexitdelaytimeexpires,alldisarmedzonesarearmed.