Installation guide

ManualsBrandsDigital Monitoring Products ManualsComputer equipment7173

Digital Monitoring Products XR500 Series Installation Guide

IntRoduCtIon

3.2 Wiring Diagram

The XR500 Series diagram below shows some of the accessory modules you can connect for use in various

applications. A brief description of each module follows in section 3.4.

Heat detectors, pull

stations, or any other

contact devices listed

for Fire Protective

Signaling can be

connected to zones

9 and 10.

Zones 9 and 10 and

Model 715 compatibility

identifier: A

Maximum operating

range: 9.7 VDC to

14.0 VDC.

Class B (Style A).

See LT-0164 for a list of

approved 4-wire smoke

detectors and power

supervision relays.

WARNING: Incorrect

connections may cause

damage to the unit.

** For listed installations, total current combined from Auxiliary

(terminals 7, 11, 25, and 27) and Bell Power (terminal 5) cannot exceed:

1.3 Amp with 50 VA transformer, 1.0 Amp Max for Auxiliary Power

1.9 Amp with 56 VA transformer, 1.0 Amp Max for Auxiliary Power and 1.5 Amp Max for Bell

DMP Transformers

Model 327 – 16.5 VAC 50 VA

Class 2 Plug-in

Model 322 – 16 VAC 56 VA

Class 2 Wire-in

Secondary Power Supply

1.0 Amps Max. charging current.

Use only 12 VDC rechargeable

batteries. DMP Models 365, 366,

367, 368, or 369. Replace

batteries every 3 to 5 years.

Bell **

12 VDC

Minimum cutoff time 5 min.

1.5 Amp Max

Minimum voltage on Auxiliary output

to process Sensor trips is 10.2 VDC.

Auxiliary Power **

Total current combined from

terminals 7, 11, 25, and 27

1.5 Amp Max

10.2 VDC to 14.0 VDC

Listed Resistors

1.0k Ohm - DMP Model 311

3.3k Ohm - DMP Model 309

10K Ohm - DMP Model 308

For Standard Line

Security burglary

applications use

Ademco Model

AB12M bell and bell

housing.

Front and Rear

tamper protection

included with

Model 350A

Attack Resistant

Enclosure.

Bell cutoff time

range is 5 to 99

minutes, non-coded.

See the XR500 Series Installation Guide (LT-0681) for a complete list of

approved 2-wire smoke detectors for zones 9, 10, and 715 Zone

Expansion Module zones.

12345678 10 11 12 13 14 15 16 17 18 199202122232425262728

+B BELL GNDSMK GNDRED YEL GRNBLK Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9+ Z9– Z10+ Z10–AC –BGND GNDGNDGND

K6 K7

Output 1Output 2

Phone Line

J10

J22

LX-Bus

Battery

Start

J23

J21

RS-232

Power

LED

PROG

Tamper

J16

Reset

Out1 Out2

Outputs 3-6

J11

¼"

Ethernet

Link LED

Activity LED

OVC

XR500 Series

Command Processor™

Panel

1k Ohm 1k Ohm1k Ohm

DISARM

ARM

Smoke

Detector

3.3k Ohm 3.3k Ohm 3.3k Ohm 3.3k Ohm

1k Ohm

Form C Relays (J2)

Output Color Code–Model 431 Harness

Output 2 N/O Orange/White

Output 2 Com White/Gray

Output 2 N/C Violet/White

Output 1 N/O Orange

Output 1 Com Gray

Output 1 N/C Violet

Annunciator Outputs (J11)

Output Color Code

Output 3 Red

Output 4 Yellow

Output 5 Green

Output 6 Black

AC Wiring must be in conduit and exit

out the left side of the enclosure.

Wiring on terminals 5 through 22 must

exit right and maintain 1/4" separation

from the AC and battery positive wiring.

Front

Tamper

Rear

Tamper

16 to 18 gauge wire

Maximum AC Wire distance

with 16 gauge wire: 70 feet

with 18 gauge wire: 40 feet

RED

BLACK

Cold Water

Pipe Earth

Ground

Bell

Zone 1

Zone 2

Zone 3

Zone 4

Zone 5

Zone 6

Zone 7

Zone 8

3.3k

Ohm

Resistor

3.3k

Ohm

Resistor

Zone Expander

Model 715

7mA @ 12 VDC

Models 715-8, 715-16

20mA @ 12 VDC

Use Listed Power Supervision

Relay rated at 12 VDC.

1k Ohm

= Supervised Circuit

Zone

22 gauge minimum

RED

YELLOW

GREEN

BLACK

1k Ohm 1k Ohm 1k Ohm

Zone Expander

Model 714

7mA @ 12 VDC

Models 714-8, 714-16

20mA @ 12 VDC

RED

YELLOW

GREEN

BLACK

RED

s s s s s

For listed installations, the Model

327 plug-in transformers shall be

installed in a DMP Model ES501

enclosure. The plug-in transformer

shall plug into a 120 VAC 60 Hz

outlet not controlled by a switch

and all

16 to 18 gauge wire

shall

run through conduit.

S S S S S S S S

S S S S

Ohm

S S

S SS SS S

1k Ohm

Zone Expander

(up to 8 zones)

Model 712-8

19mA @ 12

VDC

S S

Zone

Expander

Model 711

7mA @ 12

VDC

Ohm

Keyswitch Arming

can be connected

to any zone. See

LT-0681

s s

TYPES OF SERVICE

Central Station DACT service may be provided.

Suitable for Remote Station PPU DACT Service.

Suitable for manual fire alarm, automatic fire

alarm, sprinkler supervisory, or water flow alarm.

Suitable for Standard or Encrypted Central Station

with NET communication.

DACT Central Station using 350A Attack Resistant

enclosure.

NFPA 72

This equipment should be installed in accordance with Chapter 11 of the National

Fire Alarm Code, ANSI/NFPA 72-2002, (National Fire Protection Association,

Batterymarch Park, Quincy, MA 02269). Printed information describing proper

installation, operation, testing, maintenance, evacuation planning, and repair

service is to be provided with this equipment.

POWER LIMITED

All circuits on the Model XR500 Series comply with the requirements for inherent

power limitation and are Class 2 except the red battery wire and AC terminals.

NFPA 72 OPERATING INSTRUCTIONS

The operating instructions found on the last

page of LT-0681 must be located adjacent to

the control unit or keypad.

HOUSEHOLD FIRE WARNING

Recognized limited energy cable must be used

for connection of all initiating, indicating, and

supplementary devices.

WARNING

THIS UNIT MAY BE PROGRAMMED TO USE AN ALARM VERIFICATION

FEATURE THAT RESULTS IN DELAY OF THE SYSTEM ALARM SIGNAL FROM

THE INDICATED CIRCUITS. THE TOTAL DELAY (CONTROL UNIT PLUS

SMOKE DETECTORS) SHALL NOT EXCEED 60 SECONDS. NO OTHER

SMOKE DETECTOR SHALL BE CONNECTED TO THESE CIRCUITS UNLESS

APPROVED BY THE LOCAL AUTHORITY HAVING JURISDICTION (AHJ).

Verification

Zones

______

Control Unit

Delay

13.6 sec.

Smoke

Model

______

Detector

Delay

____sec.

In all applications where more than one wire

is under a terminal, the wire must be cut

and NOT looped around the screw terminal.

Zones 9, 10, and all

expanded zones are

suitable for Class B (as

applicable for the

initiating and signaling

line circuits per ANSI/UL

864 Table 48.2 or 48.3).

Installation limits under

local Authority Having

Jurisdiction (AHJ).

Using verification delays

on zones 9 and 10 is

optional. Use the

delays marked on the

smoke detectors.

Suitable for Bank Safe and Vault Service

with 350A Enclosure.

Suitable for Household Fire and Household

Burglary.

Suitable for Local, Police Station Connect,

Mercantile, and Proprietary with dialer

direct communication and 350A Enclosure.

Suitable for Proprietary, PPU, other

technologies, (iCOM – XR500 only), local.

SIA CP-01-2000 minimum system is

XR500, UL listed local Bell, and off

premise DACT communication to an

SCS-1R receiver plus listed compatible

keypads as indicated in the installation

guide.

Figure 1: XR500 Series Wiring Diagram