Installation guide

XR500 Series Installation Guide Digital Monitoring Products
19
InstallatIon
15.3 LX-Bus Interface Cards
YoucanaddoneInterfaceCard(Model481,462N,462P,463G,or472)totheXR500SeriesusingJ6InterfaceCard
Connector located on the board right edge. To add more than one Interface Card install a 461 Interface Adaptor
CardusingJ6InterfaceCardConnectorontheboardrightedge.The461AdaptorCardallowsuptoveInterface
Cards to be installed. Refer to the 461 Installation Sheet (LT-0736). Each Interface card provides up to 100 LX-Bus
Zones. Refer to the following tables to identify zone locations and numbers relative to J22 operation.
J22 LX-Bus Enabled
(Set J23 to “L”)
AND
One Interface Card
OR
461 Adaptor Card and
Multiple Interface Cards
LX-Bus Zone Numbers LX-Bus Zone Numbers LX-Bus Zone Numbers
1 500-599 2 600-699 2 (A) 600-699
3 (B) 700-799
4 (C) 800-899
5 (D) 900-999
J22
LX-Bus
NOT
Enabled
(J23
NOT set
to “L”)
One Interface Card
OR
461 Adaptor Card and
Multiple Interface Cards
LX-Bus Zone Numbers LX-Bus Zone Numbers
1 500-599 1 (A) 500-599
2 (B) 600-699
3 (C) 700-799
4 (D) 800-899
5 (E) 900-999
15.4 LX-Bus LEDs
The two LEDs, located near the bottom-right corner of J21 indicate data transmission and receipt. The top LED
ashesgreentoindicatethepanelistransmittingLX-Busdata.ThebottomLEDashesyellowtoindicatethepanel
is receiving LX-Bus data.
15.5 OVC LED
The Overcurrent LED (OVC) lights Red when the devices connected to the Keypad Bus and LX-Bus(es) draw more
current than the panel is rated for. The OVC is located above Outputs 1 and 2 on the panel and turns a steady Red
when lit. When the OVC LED lights Red, the LX-Bus(es) and Keypad bus shut down.
J21 Serial Connector
16.1 Description
Note: Only one connector, J21 or J22 can function at a time. Either use J21 to connect a serial device for PC Log
Reporting, or use J22 to connect a DMP Wireless device or an LX-Bus device. Operation is determined by where you
install the jumper on the J23 6-Pin header. The maximum line impedance is 100 Ohms.
ToenableJ21tooperateinRS-232mode,placeajumperonthetwopinsnexttotheletter“R”ontheJ236-Pin
headerandbrieyresetthepanelusingtheJ16jumpertoactivatetheselectedoperation.Panelprogramming
using Remote Link™ can be set up through a direct connection to a computer or through an iCOM connected to a
network. The Serial Connector allows the following operation options.
XR500 Panel XR500N/XR500E Panel
PC Log Reports PC Log Reports
Remote Link™
Programming
Additional iCOM Installed
for PC Log Reports
16.2 Computer Connection to J21
Use a straight through RS-232 Serial cable with a DB-9 female connector on one end and a DB-9 male connector on
the other end. Plug the DB-9 male connector end of the cable onto the XR500 Series panel J21 RS-232 connector.
Plug the DB-9 female connector end of the cable onto the DB-9 male connector located at the back of the computer.
Program the XR500 Series panel as needed then disconnect the computer.
Serial Data Xmit LED
Serial Data Rec(eive) LED
J22
J23
J21
RS-232
R
L
X
DB-9 Female Connector
Figure 9: J21 Serial Connection