Installation guide

ManualsBrandsDigital Monitoring Products ManualsComputer equipment7063A

Digital Monitoring Products XR500 Series Installation Guide

IntRoduCtIon

3.2 Wiring Diagram

The XR500 Series diagram below shows some of the accessory modules you can connect for use in various

applications. A brief description of each module follows in section 3.4.

Heat detectors, pull

stations, or any other

contact devices listed

for Fire Protective

Signaling can be

connected to zones

9 and 10.

Zones 9 and 10 and

Model 715 compatibility

identifier: A

Maximum operating

range: 9.7 VDC to

14.0 VDC.

Class B (Style A).

WARNING: Incorrect

connections may cause

damage to the unit.

Minimum voltage on Auxiliary output

to process Sensor trips is 10.2 VDC.

Auxiliary Power

To tal current combined from

terminals 7, 11, 25, and 27

1.5 Amp Max

10.2 VDC to 14.0 VDC

Listed Resistors

1.0k Ohm - DMP Model 311

3.3k Ohm - DMP Model 309

10K Ohm - DMP Model 308

For Standard Line

Security burglary

applications use

Ademco Model

AB12M bell and bell

housing.

Front and Rear

tamper protection

included with

Model 350A

Attack Resistant

Enclosure.

Bell cutoff time

range is 5 to 99

minutes, non-coded.

Bell

12 VDC

Minimum cutoff time 5 min.

1.5 Amp Max

12345678 10 11 12 13 14 15 16 17 18 199202122232425262728

+B BELL GND SMK GNDREDYEL GRNBLK Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9+Z9– Z10+ Z10–AC –B GND GND GNDGND

K6 K7

Output 1Output 2

Phone Line

J10

J22

LX-Bus

Battery

Start

J23

J21

RS-232

Power

LED

PROG

Tamper

J16

Reset

Out1 Out2

Outputs 3-6

J11

¼"

Ethernet

Link LED

Activity LED

OVC

XR500 Series

Command Processor™

Panel

1k Ohm1k Ohm1k Ohm

DISARM

ARM

Smoke

Detector

3.3k Ohm 3.3k Ohm 3.3k Ohm 3.3k Ohm

1k Ohm

Form C Relays (J2)

Output Color Code–Model 431 Harness

Output 2 N/OOrange/White

Output 2Com White/Gray

Output 2N/C Violet/White

Output 1N/O Orange

Output 1Com Gray

Output 1N/C Violet

Annunciator Outputs (J11)

Output Color Code

Output 3Red

Output 4Yellow

Output 5Green

Output 6Black

AC Wiring must be in conduit and exit

out the left side of the enclosure.

Wiring on terminals 5 through 22 must

exit right and maintain 1/4" separation

from the AC and battery positive wiring.

Front

Tamper

Rear

Tamper

16 to 18 gauge wire

Maximum AC Wire distance

with 16 gauge wire: 70 feet

with 18 gauge wire: 40 feet

RED

BLACK

Cold Water

Pipe Earth

Ground

Bell

Zone 1

Zone 2

Zone 3

Zone 4

Zone 5

Zone 6

Zone 7

Zone 8

3.3k

Ohm

Resistor

3.3k

Ohm

Resistor

Zone Expander

Model 715

7mA @ 12 VDC

Models 715-8, 715-16

20mA @ 12 VDC

Use Listed Power Supervision

Relay rated at 12 VDC.

1k Ohm

= Supervised Circuit

Zone

22 gauge minimum

RED

YELLOW

GREEN

BLACK

1k Ohm1k Ohm1k Ohm

Zone Expander

Model 714

7mA @ 12 VDC

Models 714-8, 714-16

20mA @ 12 VDC

RED

YELLOW

GREEN

BLACK

RED

s s s s s

he plug-in transformer shall plug

into a 120 VAC 60 Hz outlet not

controlled by a switch and all

16 to

18 gauge wire

shall run through

conduit.

S S S S S S S S

S S S S

Ohm

S S

S SS SS S

1k Ohm

Zone Expander

(up to 8 zones)

Model 712-8

19mA @ 12

VDC

S S

Zone

Expander

Model 711

7mA @ 12

VDC

Ohm

Keyswitch Arming

can be connected

to any zone.

s s

Ground

NFPA 72 OPERATING

INSTRUCTIONS

The operating instructions should be

located adjacent to the control unit or

keypad.

HOUSEHOLD FIRE WARNING

Recognized limited energy cable must

be used for connection of all initiating,

indicating, and supplementary devices.

CAUTION: DO NOT USE LOOPED WIRE

UNDER TERMINALS. BREAK WIRE RUN TO

PROVIDE SUPERVISION OF CONNECTIONS.

Zones 9, 10, and all

expanded zones are

suitable for Class B (as

applicable for the

initiating and signaling

line circuits per ANSI/UL

864 Ta ble 48.2 or 48.3).

Installation limits under

local Authority Having

Jurisdiction (AHJ).

Using verification delays

on zones 9 and 10 is

optional. Use the

delays marked on the

smoke detectors.

USE MARKING

Commercial and Residential Fire,

Burglar, Holdup, and Access Protected

Premise Unit

TYPES OF SERVICE

Suitable for Local, Police

Station Connect, Mercantile,

and Proprietary with 350A

Enclosure.

Central Station DACT service

may be provided using 350A

Attack Resistant enclosure.

Suitable for Proprietary, PPU,

other technologies, local.

Suitable for Signaling and

Remote Station PPU DACT

Service.

Suitable for manual fire alarm,

automatic fire alarm, sprinkler

supervisory, or water flow

alarm.

Suitable for Standard or

Encrypted Central Station with

NET or CELL communication.

Suitable for Bank Safe and

Vault Service with 350A

Enclosure.

Suitable for Household Fire

and Household Burglary.

Suitable for Coded and March

Time signaling.

SIA CP-01-2000 minimum

system is XR500, listed local

Bell, and off premise DACT

communication to an SCS-1R

receiver plus listed compatible

keypads as indicated in the

installation guide.

WARNING

THIS UNIT MAY BE PROGRAMMED TO USE AN ALARM VERIFICATION FEATURE THAT

RESULTS IN DELAY OF THE SYSTEM ALARM SIGNAL FROM THE INDICATED CIRCUITS.

THE TOTAL DELAY (CONTROL UNIT PLUS SMOKE DETECTORS) SHALL NOT EXCEED 60

SECONDS. NO OTHER SMOKE DETECTOR SHALL BE CONNECTED TO THESE CIRCUITS

UNLESS APPROVED BY THE LOCAL AUTHORITY HAVING JURISDICTION (AHJ).

Figure 1: XR500 Series Wiring Diagram