Installation guide

ManualsBrandsDigital Monitoring Products ManualsHome building and Decor1912XR

1912XR Installation Guide

Digital Monitoring Products, Inc. 1912XR Installation Guide

Page 1

Panel Specifications

1.1 Power supply

Transformer Input: 16.5 VAC or 40VA (Models 320 or 321) or 100VA (Model 322).

Standby Battery: 12 VDC 6.5Ah (40VA charges two batteries, 100VA charges three or four batteries))

Auxiliary Output: 12 VDC at 600mA with 40VA transformer

Bell Output: 12 VDC at 1 Amp

Inherent Power Limited

1.2 Communication

Built in Dialer communication to DMP Model SCS-1 Receivers

Built in Multiplex communication to DMP Model SCS-1 Receivers

Built in DDMX communication to DMP Model SCS-1 Receivers

Built in CID communication to non-DMP receivers

Optional Model 893 Dual Phone Line Module with phone line supervision

Can operate as a local system

1.3 Panel loops

Four 1K Ω EOL burglary loops (loops 1 to 4)

One 3.3K Ω EOL Class B powered loop with reset (loop 5)

1.4 Keypads and expanders

You can connect up to eight of the following keypads or expanders to the 1912XR keypad data bus:

• 670, 770, or 771 Alphanumeric Keypads

• 711, 714, and 715 Loop Expanders

• 5845LX Glassbreak single point detector

• 6155LX PIR single point detector

You can connect the following devices to the LX-Bus of the Model 862N, 862P, 872, and 881 Interface

Cards up to the maximum number of addresses. Also see Accessory Devices in section 4.1.

• 714 and 715 Loop Expanders - up to 25 devices

• 716 Output Expander - up to 25 devices

• 5845LX Glassbreak single point detector - up to 100 devices

• 6155LX PIR single point detector - up to 100 devices

The 714 and 715 Loop Expanders each provide four loops.

The 716 Output Expander provides four Form C relays (SPDT) and four 50mA switched grounds (open

collector) suitable for a variety of annunciation and control applications.

1.5 Output contacts

Two on-board auxiliary Form C outputs. See section 13.1. You can have up to 100 additional outputs when

using 716 Output Expanders and an 862N, 862P, 872, or 881 Interface Card.

Outputs require two Model 305 relays, each rated for 1 Amp at 30 VDC or 0.5 Amp at 120 VAC

The panel also provides four auxiliary voltage outputs rated for 50mA at 12 VDC. See section 14.1.

1.6 Enclosure specifications

The 1912XR is shipped installed in its enclosure with end of line resistors, battery leads, and programming

sheets.

Size: 12.5" x 11.5" x 3.0"

Weight: 6 lbs

Color: Black (61) or Grey (63)

Construction: 18 gauge cold rolled steel

Summary of content (36 pages)

PAGE 1
912XR Installation Guide Panel Specifications 1.1 Power supply Transformer Input: 16.5 VAC or 40VA (Models 320 or 321) or 100VA (Model 322). Standby Battery: 12 VDC 6.5Ah (40VA charges two batteries, 100VA charges three or four batteries)) Auxiliary Output: 12 VDC at 600mA with 40VA transformer Bell Output: 12 VDC at 1 Amp Inherent Power Limited 1.
PAGE 2
1912XR Installation Guide Introduction 2.1 Description The DMP 1912XR Command Processor is a powerful 12 VDC, combined burglary and fire communicator panel with battery backup. The 1912XR provides four on-board burglary loops and one on-board 12 VDC Class B powered fire loop. The fire loop has a reset capability to provide for 2-wire smoke detectors, relays, or other latching devices.
PAGE 3
1912XR Installation Guide 2.3 Partitions and areas The 1912XR can be programmed into four separate partitions. Partition 1 can be expanded into eight separate reporting areas. Partitions 2 to 4 can each be expanded into four separate reporting areas. The 1912XR panel supports up to a total of 20 areas for all partitions combined. 2.
PAGE 4
1912XR Installation Guide 2.6 About this guide The information contained in this guide is organized into four sections: Table of Contents, Introduction, Installation, and Troubleshooting. • The Table of Contents at the front of this guide lists all of the headings and subheadings used throughout each section. To the right of each heading is the section number where the information can be found.
PAGE 5
1912XR Installation Guide System Components 3.1 Description The DMP 1912XR system is made up of an alarm panel with built in communicator, an enclosure, and a 16.5 VAC transformer. You can add up to eight Security Command keypads, an expansion interface module, loop and output expanders, and initiating and indicating circuit modules. You can also connect auxiliary devices to the panel's output relays to expand the basic system.
PAGE 6
1912XR Installation Guide Accessory Devices 4.1 Loop and output modules and interface cards 711 Single Point Loop Expander The 711 module provides one Class B burglary loop for connecting burglary and non-powered fire devices. 714 Loop Expander The 714 module provides four Class B burglary loops for connecting burglary and non-powered fire devices. 715 Loop Expander The 715 module provides four 12 VDC Class B powered loops for connecting smoke detectors, glassbreak detectors, or other 2 or 4-wire devices.
PAGE 7
1912XR Installation Guide Installation 5.1 Mounting the enclosure The metal enclosure for the 1912XR must be mounted in a secure, dry place to protect the panel from damage due to tampering or the elements. It is not necessary to remove the 1912XR PC board when installing the enclosure.
PAGE 8
1912XR Installation Guide 5.2 Mounting keypads and loop expanders Security Command keypads have removable covers that allow you to easily mount the keypad to a wall or other flat surface using the screw holes provided on each corner of the base. Before mounting the base, connect the keypad wire harness leads to the keypad cable from the panel and to any device wiring run to that location.
PAGE 9
1912XR Installation Guide Primary Power Supply 6.1 AC terminals 1 and 2 Connect the transformer wires to terminals 1 and 2 on the panel. Use no more than 70 ft of 16 gauge, or 40 ft of 18 gauge, wire between the transformer and the 1912XR. Always ground the panel before applying power to any devices: The 1912XR must be properly grounded before connecting any devices or applying power to the panel. Proper grounding protects against Electrostatic Discharge (ESD) that can damage system components.
PAGE 10
1912XR Installation Guide 7.6 1912XR power requirements During AC power failure, the1912XR panel and all auxiliary devices connected to the 1912XR draw their power from the battery. All devices must be taken into consideration when calculating the battery standby capacity. Below is a list of the power requirements of the 1912XR panel.
PAGE 11
1912XR Installation Guide 7.7 Battery supervision The 1912XR tests the battery once every hour when AC power is present. The test is done at 15 minutes past the hour and lasts for five seconds. A load is placed on the battery and if its voltage falls below 11.9 VDC, a low battery is detected. If AC power has failed, a low battery is detected any time the battery voltage falls below 11.9 VDC.
PAGE 12
1912XR Installation Guide Powered Loop for 2-Wire Smoke Detectors 11.1 Terminals 12 and 13 A resettable 2-wire Class B powered loop is provided on terminals 12 (positive) and 13 (negative) of the panel. For programming purposes the loop number is 5. The loop uses a Model 309, 3.3K Ω EOL resistor provided with the panel and has an operating range of 8.8 to 14.2 VDC. The UL compatibility identifier is: A.
PAGE 13
1912XR Installation Guide 12.2 Operational parameters Each burglary protection loop detects three conditions: open, normal, and short. The parameters for each are listed below: Condition Resistance on loop Voltage on right terminal Open over 1300 ohms over 2.0 VDC Normal 600 to 1300 ohms 1.2 to 2.0 VDC Short under 600 ohms under 1.2 VDC 12.3 Loop response time A condition must be present on a loop for 500 milliseconds (1/2 second) before it's detected by the 1912XR panel.
PAGE 14
1912XR Installation Guide 12 VDC Outputs 3 to 6 14.1 Description Four 12 VDC, 50mA voltage outputs are provided on the panel's J2 Output Harness to power external relay coils or other low power indicators. The voltage outputs can be operated by all of the same functions as Relay Outputs 1 and 2. When connecting any devices to outputs 3 to 6, subtract the current draw of the device from the panel's available auxiliary power. 14.
PAGE 15
1912XR Installation Guide Reset Jumper J16 16.1 Description The reset jumper is located just above the terminal strip in the center of the circuit board and is used to reset the microprocessor of the 1912XR. To reset the panel when first installing the system, install the reset jumper before applying power to the panel. After connecting the AC and battery, remove the reset jumper.
PAGE 16
1912XR Installation Guide UNIVERSAL UL BURGLARY SPECIFICATIONS 17.1 Introduction The programming and installation specifications contained in this section must be completed when installing the 1912XR panel in accordance with any of the UL burglary standards. Additional specifications may be required by a particular standard. 17.2 Wiring All wiring must be in accordance with NEC, ANSI/NFPA 70, UL 681, and UL 611 for all burglary installations. 17.
PAGE 17
1912XR Installation Guide UL 1610 and 1076 SPECIFICATIONS Central-Station and Proprietary Burglar-Alarm Units 19.1 Multiplex network capacity The total number of panels assigned to a standard MPX or DNET receiving line of the SCS-1 Receiver System must not exceed 90. This may be increased to 180 by setting the SNRM option to NO in the SCS-1 Receiver system. This is to allow any signal from a 1912XR Command Processor to be transmitted to the receiver within 90 seconds.
PAGE 18
1912XR Installation Guide UL 365 and 609 SPECIFICATIONS Police Station Connected and Local Burglar Alarm Units and Systems 21.1 System trouble display The Status List Display must include at least one keypad that displays system monitor troubles. See section 10.3 of the 1912XR Programming Manual (LT-0171). 21.2 Entry delay The maximum entry delay used must not be more than 60 seconds when using the Model 349A Grade A housing. See section 7.3 of the 1912XR Programing Manual (LT-0171). 21.
PAGE 19
12XR Installation Guide UNIVERSAL UL and NFPA FIRE ALARM SPECIFICATIONS 22.1 Introduction The programming and installation specifications contained in this section must be completed when installing the Model 1912XR in accordance with any of the UL or NFPA fire standards. Additional specifications may be required by a particular standard. 22.2 Wiring All wiring must be in accordance with NEC, ANSI/NFPA 70. 22.3 Transformer A wire-in transformer should be used. Use the 16.
PAGE 20
1912XR Installation Guide UL 985 NFPA 74 SPECIFICATIONS Household Fire Warning System Units 23.1 Bell output definition The bell output of the Model 1912XR must be programmed to operate steady on burglary alarms and pulsed on fire alarms. See sections 8.4A and 8.4B of the 1912XR Programming Manual (LT-0171). UL 864 NFPA 71 – 72 (Chapter 9) SPECIFICATIONS Control Units for Fire-Protective Signaling Systems 24.1 Loop restoral reports The Restoral Reports option must be selected as YES or DISARM.
PAGE 21
1912XR Installation Guide 24.7 Keypad 4-wire bus The keypad and loop expander 4-wire bus must be run entirely in conduit and remain inside the same room as the panel, unless an external communication fail indicator is added. A 12 VDC relay may be wired as a communication failed indicator. Connect the positive side of the indicator to one of the voltage outputs and the negative side to keypad ground (terminal 10) of the 1912XR. See section 14.2.
PAGE 22
Digital Monitoring Products, Inc. Page 22 8 7 6 5 4 3 2 1 1k Ω DMP Model 866 37mA at 12 VDC 24 VDC 5 Amp Maximum Indicating Circuit Module Bell Trouble Bell Trouble Bell Output - Bell Output + Bell Power Input Alarm Input Ground Auxiliary Power 10k Ω EOL Resistor DMP Model 308 AUXILIARY POWER SUPPLY AC 2 AC 3 B+ Each 866 Indicating Circuit Module in alarm draws up to 35mA from its terminal 3 alarm input.
PAGE 23
Digital Monitoring Products, Inc.
PAGE 24
1912XR Installation Guide 26.3 Multiple Indicating circuit modules for zoned annunciation Dual Line Expansion J10 EPROM Socket You can have up to sixteen 866 Indicating Circuit Modules by using the relay outputs available on the 1912XR panel. All modules must be installed within an approved enclosure connected by conduit. Battery Only Restart K5 Relay Output 2 Model 305 required. Connects auxiliary power to common of Relay Output 1.
PAGE 25
1912XR Installation Guide 26.4 Dual Style D Loop module installation J9 Dual Line Expansion J10 EPROM Socket J4 Battery Only Restart Command Processor Reset J16 1 AC 2 AC 3 B+ 4 B- 5 BELL 6 GND 7 RED 8 YEL 9 GRN 10 BLK 11 SMK 12 L5+ 13 L5- 14 L1 15 GND 1k Ω 16 L2 17 L3 18 GND 19 L4 1k Ω 3.3k Ω Resistor DMP Model 309 Style D Loop Module Radionics D129 Dual Style D Module (Located internal to Model 1912XR).
PAGE 26
1912XR Installation Guide 26.5 Remote Station J9 Dual Line Expansion J10 EPROM Socket J4 Battery Only Restart Direct wire connection to 120 VAC unswitched circuit. Command Processor Reset J16 DMP Model 320 16 VAC, 40VA Transformer. 1 AC 2 AC 3 B+ 4 B- 5 BELL 6 GND 7 RED 8 YEL 9 GRN 10 BLK 11 SMK 12 L5+ 13 L5- 14 L1 15 GND 16 L2 17 L3 18 GND 19 L4 1k Ω 1k Ω 1k Ω Fire Alarm Output 3 - White/Brown Outputs 3 to 6 supply up to 50mA at 12 VDC. 1k Ω 3.
PAGE 27
Digital Monitoring Products, Inc. Page 27 8 7 6 5 4 3 2 1 1k Ω 10k Ω EOL Resistor DMP Model 308 Remote DPDT Relay Indicating Circuit Module DMP Model 866 37mA at 12 VDC Bell Trouble Bell Trouble Bell Output - Bell Output + Bell Power Input Alarm Input Ground Auxiliary Power supervised Silence switch Normally Closed contacts will open on alarm. 1 AC 2 AC 3 B+ 4 B- 5 The 866 module must be installed in the panel enclosure or in an approved enclosure connected by conduit.
PAGE 28
Digital Monitoring Products, Inc. Page 28 Note 1 Note 1 Note 1: Use EOL Termination Assembly P/N 21024-0001 (2.2k 1/2 W Resistor). Use EOL Termination Assembly P/N 21024-0003 (590 Ω 1/2 W Resistor).
PAGE 29
1912XR Installation Guide Troubleshooting Section 27.1 Description This section of the 1912XR Installation Guide provides troubleshooting information for use when installing or servicing a 1912XR system. Problem Possible Cause Solution J16 reset jumper is installed. Remove the J16 reset jumper. Open or short on the green data wire to the keypad. Check for broken or shorted wires between the keypad and panel. Bad keypad or loop expander. Replace with a new or repaired keypad or loop expander.
PAGE 30
Troubleshooting Section continued Problem Possible Cause Loops on an expansion card data bus will not set. LPX Setup shows overlapped, misssing, or extra loops. Thermal circuit breaker on panel pops on and off. Solution Too much line noise. Move wires away from RF sources. Too long of a wire run to devices. Relocate panel closer to devices. Too small a wire size or insufficient auxiliary power. Replace with a larger wire size or add an auxiliary power supply.
PAGE 31
MODEL 1912XR COMMAND PROCESSOR BURGLARY/FIRE CONTROL PANEL/COMMUNICATOR INSTALLATION GUIDE 123 2841 E.
PAGE 32
MODEL 1912XR COMMAND PROCESSOR INSTALLATION GUIDE FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
PAGE 33
TABLE OF CONTENTS Section Panel Specifications Power supply ........................................................................................ 1.1 Communication .................................................................................... 1.2 Panel loops .......................................................................................... 1.3 Keypad and expanders ........................................................................ 1.4 Output contacts ..................................
PAGE 34
TABLE OF CONTENTS Section Smoke and Glassbreak Detector Output Terminal 11 ........................................................................................ 10.1 Current rating ..................................................................................... 10.2 Powered Loop for 2-Wire Smoke Detectors Terminals 12 and 13 .......................................................................... 11.1 Protection Loops Description ...................................................................
PAGE 35
TABLE OF CONTENTS Section UL 1635 Specifications System trouble display ....................................................................... 20.1 Digital dialer telephone number ......................................................... 20.2 Entry delay ......................................................................................... 20.3 Exit delay ............................................................................................ 20.4 Test time .........................................
PAGE 36
TABLE OF CONTENTS Section California State Fire Marshal Specifications Bell output definition ........................................................................... 25.1 Wiring Diagrams Indicating circuit module installation ................................................... 26.1 Multiple indicating circuit modules ...................................................... 26.2 Multiple indicating circuit modules for zoned annunciation ................ 26.3 Dual Style D Loop Module installation .........