User`s guide
Table Of Contents
- Contents
- Figures
- Tables
- Preface
- Introduction
- Getting Started
- 2.1 Overview
- 2.2 System Requirements
- 2.3 Configuring Your System
- 2.4 Updating the Debug Monitor Firmware
- 2.4.1 Updating Firmware in a Flash ROM
- 2.4.2 Updating the Flash ROM from the AlphaBIOS S...
- 2.4.3 Updating the Flash ROM from the Windows NT ...
- 2.4.4 Updating the Flash ROM from the Debug Monit...
- 2.4.5 Updating the Flash ROM from the Alpha SRM C...
- 2.4.6 Running Firmware Update
- 2.4.7 Updating Firmware in a UVPROM
- 2.5 Switching to the Debug Monitor Firmware on Fl...
- 2.6 Debug Monitor Memory Map
- 2.7 Downloading Files
- 2.8 Execution Commands
- 2.9 Resetting the Debug Monitor
- Remote Debugging
- User Commands
- 4.1 Overview
- 4.2 Using the Commands
- 4.3 User Commands Quick Reference
- 4.4 User Commands
- apropos
- arpshow
- bcoff
- bcon
- beep
- boot
- bootadr
- bootopt
- bpstat
- cb
- cfreg
- cl
- compare
- cont
- copy
- cq
- creg
- cw
- date
- delete
- dis
- dml
- dmq
- ebuff
- edevice
- edmp
- einit
- eml
- emq
- eprom
- ereg
- eshow
- estat
- estop
- fill
- flash
- flasherase
- flboot
- flcd
- flcopy
- fldir
- flload
- flread
- flsave
- flwrite
- fwupdate
- go
- help
- iack
- ident
- init
- jtopal
- ladebug
- load
- mces
- mcheck
- memtest
- mrb
- mrl
- mrw
- mwb
- mwl
- mww
- netboot
- netload
- next
- pb
- pcishow
- pfreg
- pl
- pq
- prb
- preg
- prl
- prw
- pw
- pwb
- pwl
- pww
- rabox
- rb
- rbcfg
- rbctl
- rbiu
- riccsr
- rl
- rmode
- romboot
- romlist
- romload
- romverify
- rsys
- rw
- sb
- setbaud
- setty
- sl
- sq
- step
- stop
- sum
- sw
- swpipl
- sysshow
- tip
- version
- wabox
- wb
- wbcfg
- wbctl
- wbiu
- wiccsr
- wl
- wrfen
- wsys
- ww
- Support, Products, and Documentation
- Index
User Commands 4–19
User Commands
bootopt
The bootopt command can also be used to select a ROM image based on its position
in the ROM. Specifying the type as #0 selects the whole ROM. Specifying the type
as #1 selects the first image; #2 selects the second image, and so on. The bootopt
command is not supported for the EB64+, EB66, or EB64.
Example
AlphaPC 64> bootopt
Predefined bootoptions are...
“0” “Alpha Evaluation Board Debug Monitor” “DBM”
“1” “The Windows NT Operating System” “NT”
“2” “OpenVMS” “VMS”
“3” “DIGITAL UNIX, formerly DEC OSF/1” “UNIX”
“7” “Linux” “Milo”
“8” “VxWorks. Real-Time Operating System” “VxWorks”
“10” “Serial ROM (SROM)” “SROM”
O/S type selected: “OpenVMS”
....Firmware type: “Alpha SRM Console”
AlphaPC 64> bootopt 0
O/S type selected: “Alpha Evaluation Board Debug Monitor”
....Firmware type: “Alpha Evaluation Board Debug Monitor”
AlphaPC 64> bootopt nt
O/S type selected: “The Windows NT Operating System”
....Firmware type: “Windows NT Firmware”
AlphaPC 64> bootopt #1
Firmware image 1 selected.
....Firmware type: “Unknown”
AlphaPC 64> bootopt unix
O/S type selected: “DIGITAL UNIX, formerly DEC OSF/1”
....Firmware type: “Alpha SRM Console”
AlphaPC 64> bootopt #0
Load and boot entire ROM at address zero.
....Firmware type: “Unknown”
AlphaPC 64> bootopt
Predefined bootoptions are...
“0” “Alpha Evaluation Board Debug Monitor” “DBM”
“1” “The Windows NT Operating System” “NT”
“2” “OpenVMS” “VMS”
“3” “DIGITAL UNIX, formerly DEC OSF/1” “UNIX”
“7” “Linux” “Milo”
“8” “VxWorks. Real-Time Operating System” “VxWorks”
“10” “Serial ROM (SROM)” “SROM”
Load and boot entire ROM at address zero.
....Firmware type: “Unknown”