User`s guide
Table Of Contents
- Contents
- Figures
- Tables
- Preface
- Introduction
- Getting Started
- 2.1 Overview
- 2.2 System Requirements
- 2.3 Configuring Your System
- 2.4 Updating the Debug Monitor Firmware
- 2.4.1 Updating Firmware in a Flash ROM
- 2.4.2 Updating the Flash ROM from the AlphaBIOS S...
- 2.4.3 Updating the Flash ROM from the Windows NT ...
- 2.4.4 Updating the Flash ROM from the Debug Monit...
- 2.4.5 Updating the Flash ROM from the Alpha SRM C...
- 2.4.6 Running Firmware Update
- 2.4.7 Updating Firmware in a UVPROM
- 2.5 Switching to the Debug Monitor Firmware on Fl...
- 2.6 Debug Monitor Memory Map
- 2.7 Downloading Files
- 2.8 Execution Commands
- 2.9 Resetting the Debug Monitor
- Remote Debugging
- User Commands
- 4.1 Overview
- 4.2 Using the Commands
- 4.3 User Commands Quick Reference
- 4.4 User Commands
- apropos
- arpshow
- bcoff
- bcon
- beep
- boot
- bootadr
- bootopt
- bpstat
- cb
- cfreg
- cl
- compare
- cont
- copy
- cq
- creg
- cw
- date
- delete
- dis
- dml
- dmq
- ebuff
- edevice
- edmp
- einit
- eml
- emq
- eprom
- ereg
- eshow
- estat
- estop
- fill
- flash
- flasherase
- flboot
- flcd
- flcopy
- fldir
- flload
- flread
- flsave
- flwrite
- fwupdate
- go
- help
- iack
- ident
- init
- jtopal
- ladebug
- load
- mces
- mcheck
- memtest
- mrb
- mrl
- mrw
- mwb
- mwl
- mww
- netboot
- netload
- next
- pb
- pcishow
- pfreg
- pl
- pq
- prb
- preg
- prl
- prw
- pw
- pwb
- pwl
- pww
- rabox
- rb
- rbcfg
- rbctl
- rbiu
- riccsr
- rl
- rmode
- romboot
- romlist
- romload
- romverify
- rsys
- rw
- sb
- setbaud
- setty
- sl
- sq
- step
- stop
- sum
- sw
- swpipl
- sysshow
- tip
- version
- wabox
- wb
- wbcfg
- wbctl
- wbiu
- wiccsr
- wl
- wrfen
- wsys
- ww
- Support, Products, and Documentation
- Index
4–10 User Commands
User Commands
4.4 User Commands
The following section contains complete descriptions and examples of the Debug
Monitor commands. The commands are listed in alphabetical order.
Ethernet Commands
edevice device_number Selects a registered Ethernet device.
eshow none Displays all registered Ethernet devices.
ereg none Displays the Ethernet controller registers.
estat none Displays Ethernet statistics.
einit none Initializes Ethernet controller and displays the Ethernet
hardware address.
estop none Stops the Ethernet controller.
ebuff address Sets the base address for Ethernet DMA buffers.
edmp status Sets or clears display of packets received or transmitted.
eprom status Sets or clears flag for receiving all packets (promiscuous
mode).
arpshow none Displays all known address resolution protocol (ARP)
entries.
Diagnostic Commands
beep duration, frequency Causes speaker to beep for the specified duration and
frequency.
mcheck state Controls the reporting of hardware error conditions
(machine checks).
memtest iterations,
start_address,
end_address,
increment, mcheck,
stop_drivers
Tests memory range. Uses longword accesses to memory.
Table 4–1 Command Summary Table
(Sheet 7 of 7)
Command Parameters Description