User`s guide
Table Of Contents
- Contents
- Figures
- Tables
- Preface
- Introduction
- Getting Started
- 2.1 Overview
- 2.2 System Requirements
- 2.3 Configuring Your System
- 2.4 Updating the Debug Monitor Firmware
- 2.4.1 Updating Firmware in a Flash ROM
- 2.4.2 Updating the Flash ROM from the AlphaBIOS S...
- 2.4.3 Updating the Flash ROM from the Windows NT ...
- 2.4.4 Updating the Flash ROM from the Debug Monit...
- 2.4.5 Updating the Flash ROM from the Alpha SRM C...
- 2.4.6 Running Firmware Update
- 2.4.7 Updating Firmware in a UVPROM
- 2.5 Switching to the Debug Monitor Firmware on Fl...
- 2.6 Debug Monitor Memory Map
- 2.7 Downloading Files
- 2.8 Execution Commands
- 2.9 Resetting the Debug Monitor
- Remote Debugging
- User Commands
- 4.1 Overview
- 4.2 Using the Commands
- 4.3 User Commands Quick Reference
- 4.4 User Commands
- apropos
- arpshow
- bcoff
- bcon
- beep
- boot
- bootadr
- bootopt
- bpstat
- cb
- cfreg
- cl
- compare
- cont
- copy
- cq
- creg
- cw
- date
- delete
- dis
- dml
- dmq
- ebuff
- edevice
- edmp
- einit
- eml
- emq
- eprom
- ereg
- eshow
- estat
- estop
- fill
- flash
- flasherase
- flboot
- flcd
- flcopy
- fldir
- flload
- flread
- flsave
- flwrite
- fwupdate
- go
- help
- iack
- ident
- init
- jtopal
- ladebug
- load
- mces
- mcheck
- memtest
- mrb
- mrl
- mrw
- mwb
- mwl
- mww
- netboot
- netload
- next
- pb
- pcishow
- pfreg
- pl
- pq
- prb
- preg
- prl
- prw
- pw
- pwb
- pwl
- pww
- rabox
- rb
- rbcfg
- rbctl
- rbiu
- riccsr
- rl
- rmode
- romboot
- romlist
- romload
- romverify
- rsys
- rw
- sb
- setbaud
- setty
- sl
- sq
- step
- stop
- sum
- sw
- swpipl
- sysshow
- tip
- version
- wabox
- wb
- wbcfg
- wbctl
- wbiu
- wiccsr
- wl
- wrfen
- wsys
- ww
- Support, Products, and Documentation
- Index
4–78 User Commands
User Commands
ident
ident
The ident command displays revision control system (RCS) ID strings found in the
specified memory range.
Format
ident [start_address [end_address]]
Parameters
start_address
Specifies a hexadecimal number that represents a legal address at which to start
searching for RCS keywords. The default value is the boot address.
end_address
Specifies a hexadecimal number that represents a legal address at which to end the
search for RCS keywords. The default value is the boot address plus 70
16
.
Description
The ident command identifies the revision of files used to build images that were
loaded into memory by searching for all occurrences of the pattern $keyword: ...$ in
the specified memory range. This command is based on the assumption that RCS
was used for version control on the source files on the host development system.
RCS is supplied with the DIGITAL UNIX operating system.