User's Manual
Table Of Contents
- Operator’s Manual
- Digital
- Control
- Incorporated
- DCI Headquarters 19625 62nd Ave. S., Suite B-103 Kent, Washington 98032 USA Tel 425 251 0559 / 800 288 3610 Fax 253 395 2800 E-mail DCI@digital-control.com www.digitrak.com
- Important Notice
- Safety Precautions and Warnings
- Safety Precautions and Warnings (Continued)
- _
- Introduction
- _
- Receiver
- Power On
- Toggle and Trigger Switches
- Speaker and Audible Tones
- Adjusting Screen Contrast
- Main Menu
- Locate Menu
- Set US Menu
- Low Fre/High Fre Menu
- Configure Menu
- Changing the Telemetry Channel
- 1-Point Calibration
- 2-Point Calibration (In-ground Calibration)
- Changing the Grade Mode
- Changing the Depth Measurement Mode
- Cold Screen / Normal Screen
- Tele Option A/B
- Locator DL / No Locator DL (Enabling and Disabling DataLog Menus)
- Set Roll / Unset Roll (Enabling and Disabling Roll Offset Function)
- Remote Display
- _
- Transmitter
- _
- Battery Charger
- _
- Locating
- _
- The Target Steering® Function
- _
- Cable System
- Cable System Components
- Non-DCI Supplies Required for Operating the Cable System
- Connecting Power Supply to Power Source and Cable Transmitter
- Grounding the Cable Transmitter
- Cable Transmitter On/Off
- Calibrating the Cable Transmitter
- Enabling the Roll Offset Function on the Remote Display
- Locating Using the Cable System
- Viewing Transmitter Depth or Predicted Depth
- Viewing Status of Cable System Power Source
- Target Steering Function Using the Cable System
- Troubleshooting
- _
- Appendix
- Depth Increase in Inches (Centimeters) per 6-foot (1.8 meter) Rod
- Depth Increase in Inches (Centimeters) per 10-foot (3-meter) Rod
- Depth Increase in Inches (Centimeters) per 15-foot (4.6-meter) Rod
- Percent of Grade to Degree Conversions (0.1% Pitch Transmitters or Sensitive Pitch)
- Degree to Percent of Grade Conversions (0.1% Pitch Transmitters)
- Calculating Depth Based on Distance Between FLP and RLP
- LIMITED WARRANTY
Transmitter
For the mini transmitter (8.00 in./203.2 mm long), each slot should begin at least 1.25 in. (32 mm) from
the front or index cap end of the transmitter and must be at least 3.75 in. (95 mm) long (see figure below).
Battery
Compartment End
Index
Cap End
Slot Position
Slot Length
3.75 in. (95 mm)
1.25 in.
(32 mm)
Mini Transmitter Housing Slot Requirements
For the long-range transmitter (19.00 in./482.6 mm long), each slot should begin at least 2.0 in. (51 mm)
from the front or index cap end of the transmitter and must be at least 13.0 in. (330 mm) long (see figure
below).
Battery Compartment End Index Cap End
Slot Position
Slot Length
13.0 in. (330 mm)
2.0 in.
(51 mm)
Long-Range Transmitter Housing Slot Requirements
General Transmitter Care Instructions
¾ Clean the springs in the battery compartment and the threads of the battery cap and O-ring.
Emery cloth can also be used to remove any oxidation buildup.
¾ Verify that the transmitter fits snugly into the housing. It may be necessary to wrap the transmitter
with tape or O-rings.
¾ Send in the Product Registration card for the 90-day limited warranty.
DigiTrak
®
Eclipse
®
Operator’s Manual 41