User's Manual
Table Of Contents
- Operator’s Manual
- Digital
- Control
- Incorporated
- DCI Headquarters 19625 62nd Ave. S., Suite B-103 Kent, Washington 98032 USA Tel 425 251 0559 / 800 288 3610 Fax 253 395 2800 E-mail DCI@digital-control.com www.digitrak.com
- Important Notice
- Safety Precautions and Warnings
- Safety Precautions and Warnings (Continued)
- _
- Introduction
- _
- Receiver
- Power On
- Toggle and Trigger Switches
- Speaker and Audible Tones
- Adjusting Screen Contrast
- Main Menu
- Locate Menu
- Set US Menu
- Low Fre/High Fre Menu
- Configure Menu
- Changing the Telemetry Channel
- 1-Point Calibration
- 2-Point Calibration (In-ground Calibration)
- Changing the Grade Mode
- Changing the Depth Measurement Mode
- Cold Screen / Normal Screen
- Tele Option A/B
- Locator DL / No Locator DL (Enabling and Disabling DataLog Menus)
- Set Roll / Unset Roll (Enabling and Disabling Roll Offset Function)
- Remote Display
- _
- Transmitter
- _
- Battery Charger
- _
- Locating
- _
- The Target Steering® Function
- _
- Cable System
- Cable System Components
- Non-DCI Supplies Required for Operating the Cable System
- Connecting Power Supply to Power Source and Cable Transmitter
- Grounding the Cable Transmitter
- Cable Transmitter On/Off
- Calibrating the Cable Transmitter
- Enabling the Roll Offset Function on the Remote Display
- Locating Using the Cable System
- Viewing Transmitter Depth or Predicted Depth
- Viewing Status of Cable System Power Source
- Target Steering Function Using the Cable System
- Troubleshooting
- _
- Appendix
- Depth Increase in Inches (Centimeters) per 6-foot (1.8 meter) Rod
- Depth Increase in Inches (Centimeters) per 10-foot (3-meter) Rod
- Depth Increase in Inches (Centimeters) per 15-foot (4.6-meter) Rod
- Percent of Grade to Degree Conversions (0.1% Pitch Transmitters or Sensitive Pitch)
- Degree to Percent of Grade Conversions (0.1% Pitch Transmitters)
- Calculating Depth Based on Distance Between FLP and RLP
- LIMITED WARRANTY
Receiver
Low Fre/High Fre Menu
Frequency Settings
The frequency menu option will display as either Low Fre (low frequency) or High Fre (high frequency).
If you see Low Fre, you are being asked if you would like to change to the low-frequency setting; this
means the receiver is set to receive high-frequency (12-kHz) signals. If you are running the standard
Eclipse transmitter (black tube), the Eclipse dual-frequency transmitter (lavender tube) in single-high (SH)
or dual-high (DH) mode, or the mini transmitter (gray tube), the receiver should display Low Fre.
If you see High Fre, you are being asked if you would like to change to the high-frequency setting, which
means the receiver is currently set to receive low-frequency signals. If you are running the dual-frequency
transmitter in dual-low (DL) mode, the receiver should display High Fre.
NOTE: The only time you should see High Fre is when you are using the dual-frequency trans-
mitter in dual-low (DL) mode. For additional information, see the Transmitter section.
Changing the Frequency Setting
To change the frequency setting, select the frequency option that is shown, and click the trigger.
Configure Menu
The Configure menu options are listed and described briefly in the table given below. More detailed infor-
mation and instructions for each menu option follow this listing.
Most of the menu options are presented as a question. For example, if you see ° Grade you are being
asked, “Do you want to measure pitch in degrees?” If the answer is yes, then click the trigger. The menu
item will then change to show % Grade.
16 DigiTrak
®
Eclipse
®
Operator’s Manual