User's Manual
Table Of Contents
- Operator’s Manual
- Digital
- Control
- Incorporated
- DCI Headquarters 19625 62nd Ave. S., Suite B-103 Kent, Washington 98032 USA Tel 425 251 0559 / 800 288 3610 Fax 253 395 2800 E-mail DCI@digital-control.com www.digitrak.com
- Important Notice
- Safety Precautions and Warnings
- Safety Precautions and Warnings (Continued)
- _
- Introduction
- _
- Receiver
- Power On
- Toggle and Trigger Switches
- Speaker and Audible Tones
- Adjusting Screen Contrast
- Main Menu
- Locate Menu
- Set US Menu
- Low Fre/High Fre Menu
- Configure Menu
- Changing the Telemetry Channel
- 1-Point Calibration
- 2-Point Calibration (In-ground Calibration)
- Changing the Grade Mode
- Changing the Depth Measurement Mode
- Cold Screen / Normal Screen
- Tele Option A/B
- Locator DL / No Locator DL (Enabling and Disabling DataLog Menus)
- Set Roll / Unset Roll (Enabling and Disabling Roll Offset Function)
- Remote Display
- _
- Transmitter
- _
- Battery Charger
- _
- Locating
- _
- The Target Steering® Function
- _
- Cable System
- Cable System Components
- Non-DCI Supplies Required for Operating the Cable System
- Connecting Power Supply to Power Source and Cable Transmitter
- Grounding the Cable Transmitter
- Cable Transmitter On/Off
- Calibrating the Cable Transmitter
- Enabling the Roll Offset Function on the Remote Display
- Locating Using the Cable System
- Viewing Transmitter Depth or Predicted Depth
- Viewing Status of Cable System Power Source
- Target Steering Function Using the Cable System
- Troubleshooting
- _
- Appendix
- Depth Increase in Inches (Centimeters) per 6-foot (1.8 meter) Rod
- Depth Increase in Inches (Centimeters) per 10-foot (3-meter) Rod
- Depth Increase in Inches (Centimeters) per 15-foot (4.6-meter) Rod
- Percent of Grade to Degree Conversions (0.1% Pitch Transmitters or Sensitive Pitch)
- Degree to Percent of Grade Conversions (0.1% Pitch Transmitters)
- Calculating Depth Based on Distance Between FLP and RLP
- LIMITED WARRANTY
Receiver
Speaker and Audible Tones
The receiver has a speaker below the trigger area of the handle. The speaker emits warning tones if the
transmitter’s temperature is increasing to indicate that appropriate and immediate attention is required.
Adjusting Screen Contrast
There are two techniques for adjusting the display screen contrast to gradually lighten or darken it. The
receiver must be in locate mode for either technique.
¾ Hold in the trigger while pushing the toggle several times to the right (to lighten) or to the left (to
darken) the display’s contrast.
¾ Push and hold the toggle to the right (to lighten) or to the left (to darken) while clicking the trigger
for the desired contrast.
NOTE: The remote display screen is adjusted in the same way as the receiver except the execute
button serves as the trigger and the toggle arrows work in the same manner as the toggle
switch (see Remote Display section in this manual).
Main Menu
The main system display for the Eclipse software shows the current date/time, the CPU version, and the
DSP version when the unit is first turned on (an example is shown in the figure below). It also shows the
main menu options—Locate, Power Off, Set US, Configure, and Low Fre/High Fre (this option can be
viewed by toggling right past Configure). When an item is selected with the toggle, it is indicated by
arrows on the right and left, as shown in the figure below where the Locate menu is selected.
CPU Version: r1.1.33.1 Oct 30 2006
Tele Ver: 2.12EDRp DSP Ver: 0-4- 4
®
Configure
Power Off
Set US
Locate
Receiver Main Menu Display
12 DigiTrak
®
Eclipse
®
Operator’s Manual