802.11AC Wireless Access Point Installation Manual Manual Version: v1.
802.11AC Wireless Access Point Installation Manual Content Content Chapter 1 Device Introduction ............................................. 1-1 Chapter 2 Preparation for Installation ................................. 2-1 2.1 Installation Precautions .................................................................2-1 2.2 Installation Environment Requirements .......................................2-2 2.3 Equipment Accessories .................................................................2-2 2.
802.11AC Wireless Access Point Installation Manual Chapter 1 Device Introduction Chapter 1 Device Introduction WL8200 Series Wireless AP ( Access Point) is the new 1000Mb wireless AP device based on 802.11n and 802.11AC standard with high performance from DigitalChina Networks Limited (DCN). 802.11AC Wireless Access Point can work in the band of 2.4GHz and 5GHz. It can provide higher bandwidth and cover wider range. The uplink of this AP adopts the 1000Mb Ethernet port which supports PoE power.
802.11AC Wireless Access Point Installation Manual WL8200-I3 Chapter 1 Device Introduction • IEEE802.11a/b/g/n/ac Built-in antenna: • Double Radiofrequency •2.4G gain 4.5dBi Default: ≤12.92W Using USB: ≤20W •5G gain 4.5dBi The shape size and weight of WL8200 series indoor AP is as below: Table 1-2 the shape size and weight Product Model WL8200 series（W×D×H） Shape Size 183 x 150 x 42 mm 1-2 Weight 0.
802.11AC Wireless Access Point Installation Manual Chapter 2 Preparation for Installation Chapter 2 Preparation for Installation 2.1 Installation Precautions Only allow the professionals installing and disassembling the device and its annex. Before the installation and configuration, please read the related security introduction carefully. z Adopt the appropriate security measures to avoid the personal injury and equipment damage.
802.11AC Wireless Access Point Installation Manual Chapter 2 Preparation for Installation particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver.
802.
02.11AC Wireless Access Point Installation Manual Chapter 3 AP Installation Chapter 3 AP Installation Because the installation position of WL8200 series indoor AP is high normally, the maintenance personal cannot maintain and debug through the console port to login the device after installation. We suggest user conducting the basic configuration according to need before installing the AP to the appointed position. 3.
802.11AC Wireless Access Point Installation Manual Chapter 3 AP Installation 3.2 Checking before Installation Please check the following items before the AP installation: z Please power to the AP first and connect the AP to the Ethernet, then check the LED status to make sure the AP can work normally. z Please ensure to complete the wiring in the position of AP installation. z WL8200 series indoor AP supports 802.3af and 802.3at standard PoE (Power over Ethernet) power.
802.11AC Wireless Access Point Installation Manual Chapter 3 AP Installation Fig 3-2 wall mounting screws When installed with wall hanging method, please connect the Ethernet cable to the AP first and then install the AP on the wall mounting bracket. (1) Connect the AP to the wired LAN by using the cable (2) Mark the positions of two holes on the wall and the distance between them is 65 mm.
802.11AC Wireless Access Point Installation Manual Chapter 3 AP Installation 1. The width of T-keel is from 12mm to 30mm. 2. This installation method is only applied to the T-keel but not the other kinds of keels. The T-keel mounting kit includes two plastic mounting kits and two fixing screws, and they can be found in the accessory bag. Fig 3-4 mounting kit WL8200 series AP provides two kinds of mounting kits whose width are 15cm and 24cm.
802.11AC Wireless Access Point Installation Manual Chapter 3 AP Installation Fig 3-6 Fix the AP on the T-keel Step 3: Whirl the AP by counterclockwise and closing to the T-keel to make the two diagonal slots of the mounting kit buckle the T-keel. At the same time, the two elastic stoppers on the mounting kit buckle the T-keel for locking. After complete the installation, it is as below: Fig 3-7 Complete the AP installation 3.
802.11AC Wireless Access Point Installation Manual Chapter 3 AP Installation User can use the Ethernet cable to connect the Ethernet interface of the AP and the switch which supports PoE function to power to the AP. WL8200 series adopts the 802.3af/802.3at PoE power supply. When the USB is not used, it adopts the 802.3af PoE power supply; if the USB is used, it should adopt the 802.3at PoE power supply. The device provides two Ethernet interfaces of LAN1 and LAN2.
802.11AC Wireless Access Point Installation Manual Chapter 3 AP Installation 3.6 Connect AP to Internet In the actual use, AP can be uplink connected to the Internet or MAN through the Ethernet port. Connect the Ethernet port of the AP to the switch port to achieve the uplink connection.
