Instruction manual

13
STARTER MOTOR CURRENT DRAW
120 VOLT STARTER MOTORS A
Use Line Current Adapter, Tool part number ïçíëè,
when checking current draw on 120 volt starter
volt starter test to check the current draw and free
running RPM of motor.
̸» º±´´±©·²¹ ¬»-¬ °®±½»¼«®» ³«-¬ ¾»
«-»¼ ¬± ¿ª±·¼ ¿²§ ¿½½·¼»²¬¿´ -¸±½µ
¸¿¦¿®¼ ¬± ¬¸» -»®ª·½» ¬»½¸²·½·¿²ò
1. Insert BLACK test lead from adapter, Tool part
number ïçíëè, into the
ÝÑÓ
receptacle in
meter.
2. Insert white test lead from adapter, Tool part
number ïçíëè, into the receptacle in
meter.
3. Plug the adapter cord (female end) into the switch
box receptacle of the starter motor.
4. Plug the adapter cord (male end) into the
previously tested wall outlet.
5. Rotate selector to A position.
maximum allowable amperage draw for motor
being tested.
7. Depress starter switch button. When meter
reading stabilizes, (approximately 3 seconds)
shown in Table 4.
ÝßËÌ×ÑÒæ ׺ ¿³°»®¿¹» ·- ¸·¹¸»® ¬¸¿²
-¬±° ¬¸» ¬»-¬ÿ ß² ¿³°»®¿¹» ®»¿¼·²¹
¸·¹¸»® ¬¸¿² ²«³¾»® ·² ½¸¿®¬ô ·²¼·½¿¬»-
¿ -¸±®¬»¼ -¬¿®¬»® ³±¬±®ô ©¸·½¸ ½±«´¼ ¾»
¼¿²¹»®±«-ò
ïîð ʱ´¬ ßÝ Í¬¿®¬»® Ó±¬±® Ý«®®»²¬ Ü®¿©
©·¬¸ Ô·²» Ý«®®»²¬ ß¼¿°¬»®
check RPM using vibration tachometer, Tool part
number ïçîðð.
Table 4.
10.If the starter motor does not meet the given
Manual, Section 7.
ÌßÞÔÛ ì
ïîð ÊÑÔÌ ÍÌßÎÌÛÎ ÓÑÌÑÎ ÍÐÛÝ×Ú×ÝßÌ×ÑÒÍ
ÍÌßÎÌÛÎ ÓÑÌÑÎ
×ÜÛÒÌ×Ú×ÝßÌ×ÑÒ
ÓßÈ×ÓËÓ
ßÓÐÛÎßÙÛ
Ó×Ò×ÓËÓ
ÎÐÓ
American Bosch
SME–110–C3
SME–110–C6
SME–110–C8
3.5 7400
American Bosch
06026–28–M030SM
3.0 7400
Mitsubishi
J282188
3.5 7800
Briggs & Stratton
2.7 6500
ÐËÍØ
ÍÉ×ÌÝØ ÌÑ
ßÝÌ×ÊßÌÛ
ÍÌßÎÌÛÎ
ÌßÝØÑÓÛÌÛÎ
ÎÛßÜ ÎÐÓ ÑÚ
ÍÌßÎÌÛÎ ÓÑÌÑÎ
ßÝ Ô×ÒÛ ÊÑÔÌßÙÛ ÓËÍÌ
ÞÛ ÒÑ ÔÛÍÍ ÌØßÒ ïïð ÊÑÔÌÍ