Instruction manual

11
DC AMPERAGE OUTPUT CHECK
Í»» Ò±¬» Þ»´±© Ú±® ïñî ß³° ¿²¼ ͧ-¬»³ í
ú ì ß´¬»®²¿¬±®-
Í»» п¹» ïì º±® Í°»½·¿´ ײ-¬®«½¬·±²- ±² ݸ»½µ·²¹
ÜÝ ß³°»®¿¹» Ñ«¬°«¬ ±º ïê ¿²¼ îð ß³° λ¹«´¿¬»¼
ͧ-¬»³
1. Insert RED test lead into receptacle in
meter.
2. Insert BLACK test lead into
ÝÑÓ
receptacle in
meter.
3. Rotate selector to position.
4. Attach RED test clip to DC output terminal.
5. Attach BLACK test clip to õ (positive)
battery terminal. (See note for System 3 & 4
alternators.)
6. With engine running at 3600 RPM, DC output
for alternator type shown in Table 3.
ÒÑÌÛæ ïñî ßÓÐ ßÒÜ ÍÇÍÌÛÓ í ú ì
ÜÝ ßÓÐÛÎßÙÛ ÑËÌÐËÌ ÝØÛÝÕæ
Follow DC output check procedure as described
above through step 4.
At step 5, attach BLACK test clip to ground.
At step 6, with engine running at 2800 RPM,
DC output should be no less than 0.5 amp.
ÜÝ ß³°»®¿¹» Ñ«¬°«¬ ݸ»½µ
* Connect test leads before starting engine. Be sure
connections are secure. If a test lead vibrates
loose while engine is running, the regulator/
** Amperage will vary with battery voltage. If battery
voltage is at its maximum, the amperage will be
less than the higher value shown.
ÌßÞÔÛ í
ßÔÌÛÎÒßÌÑÎ ÌÇÐÛ ÜÝ ÑËÌÐËÌ
1/2 AMP, SYSTEM 3 & 4 .5 AMP
DC ONLY (VANGUARD™ ) (1.2 AMP) 1.2 AMP
DC ONLY (MODEL 130000) (1.5 AMP) 1.5 AMP
DC ONLY (3 AMPS) **2–4 AMPS
DUAL CIRCUIT **2–4 AMPS
*QUAD-CIRCUIT **3–8 AMPS
*5 AMPS REGULATED **3–5 AMPS
*9 AMPS REGULATED **3–9 AMPS
*10 AMPS REGULATED **3–10 AMPS
*16 AMPS REGULATED **3–16 AMPS
*20 AMPS REGULATED **3–20 AMPS
ÌÛÍÌ ÔÛßÜ
ÌÑ ÜÝ ÑËÌÐËÌ Ð×Ò
•ÞËÓÐŒ ÑÒ ÝÑÒÒÛÝÌÑÎ
×ÒÜ×ÝßÌÛÍ ÌØÛ ÜÝ
ÑËÌÐËÌ Ð×Ò ÔÑÝßÌ×ÑÒ
ÔÛßÜ ÌÑ
ÐÑÍ×Ì×ÊÛ
ÞßÌÌÛÎÇ
ÌÛÎÓ×ÒßÔ
ßÝ
ÑËÌÐËÌ
Ð×Ò
ÜÝ
ÑËÌÐËÌ
Ð×Ò
ÜËßÔ
Ý×ÎÝË×Ì ÍÇÍÌÛÓ