Network Video Recorder Quick Installation Guide DS-8200-RM Pro Series DS-8209/8212/8216/8220/8225/8232-RM Pro Quality Service Group July , 2013 Information in this document is subject to change without notice. © Copyright 2013, DIGIEVER Corporation. All rights reserved.
Quick Installation Guide Thank you for choosing DIGISTOR Network Video Recorder. The following quick guide will lead you to complete the installation and configuration of the NVR. Please read the following description carefully. Pre-installation Notice Please make sure the following items are prepared for installing DIGOSTOR DS-8200-RM Pro Series.
Graphics Adapter AGP or PCI-Express, minimum 1024×768, 16 bit colors, 1G memory or above Note: It is highly recommended to use a graphics adaptor which provides higher than resolutions 1024 x 768 in order to experience the full benefits of the software. Make sure the display DPI setting is set to default at 96DPI To set DPI value, right-click on desktop, choose “Settings” tab >> “Advanced” >> “General.” CD-ROM Drive It is necessary to read the operating instructions in the provided CD-ROM.
Package Contents NVR Network Video Recorder Power Cord Ethernet Cable Screw Bag Product CD 4
Hardware Description Front View 1. Rear View LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4, HDD5, HDD6, HDD7, HDD8 2. Power button 3. USB BACKUP button - Auto video backup 4. USB 3.0 x 1 (Support auto video backup) 5. HDD1 6. HDD2 7. HDD3 8. HDD4 9. HDD5 10. HDD6 11. HDD7 12. HDD8 13. Gigabit LAN x 2 14. USB 2.0 x 4 15. eSATA x 2 (reserved) 16. VGA output 17. HDMI output 18. DI/DO (4 in 2 out) Right to left: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO1, DO2 19. Reset button 20.
Hard Disk Installation Please follow the steps as illustrated below to install the hardware: Take out the disk tray from NVR. Connect the Ethernet cable to the port of Giga LAN. Install the hard disk in each tray Connect the power cord to power and lock the disk with four screws. connector. Ensure the disk holes match the holes at the base of disk tray. Insert the disk tray into NVR and Turn on the server and there is a push it to the end.
Connection to DIGISTOR NVR Please insert the product CD-ROM on a PC to install EZ Search and S-NVR Decoder. Finally, you can start Quick Configuration on a web page. Install EZ Search for finding NVR in the network. Install S-NVR Decoder. Connect to the configured NVR and install the ActiveX control. Install EZ Search Please execute the product CD and click “Install EZ Search.” Follow the instructions to install and the EZ Search will run automatically.
Connect to NVR 1. Connect to DIGISTOR After setting the EZ Search and S-NVR Decoder, the user can connect to the monitoring page by the following two options: 1) EZ Search Once you click “Connect” or double click the selected NVR list, the IE browser will pop up automatically. 2) IE browser Log in to the system by entering its IP address in IE browser.
2. Enter a user name and password Log in the NVR with the default administer account (user name: admin, password: admin). 3.
Quick configuration After you install the ActiveX control, the system will direct you to set Quick Configuration in 5 steps. Follow the instructions of the Overview of wizard to complete the system setup. Once the five steps of Quick Configuration are complete, you can click “Start Liveview” to start monitoring. For further details of Quick Configuration, please refer to the user manual. When the live view is displayed, you have successfully installed the DIGISTOR NVR.
