Operating instructions

CALIBRATION
TEST EQUIPMENT
REPLACEMENT
Calibration Test Equipment Chart
This chart compares TM 500
product performance to that of older
Tektronix equipment . Only those
characteristics
where significant specification differences occur,
are listed . In some cases the new instrument
may not be a total functional replacement . Additional support
instrumentation may be needed or a change
in
calibration
procedure may be necessary .
wave
available at 5, 2, and 1 ns .
TG 501
- Marker outputs, 5 sec to 1 ns . Sine-
wave available at 5, 2, and 1 ns .
Trigger output - slaved to
marker
output from 5 sec
through 100 ns .
One time-mark can
be generated at
a time .
TG 501 -
Marker
outputs,
5 sec to 1 ns . Sine-
wave available at 5, 2, and 1 ns .
Trigger output - slaved to
marker
output from 5 sec through 100
ns .
One time-mark can
be generated at
a time .
REV . A, OCT 1975
184
2901
Comparison of Main Characteristics
- 10 V output
.
- Risetime 0 .5 ns ; 30 to 250 ns
Pretrigger pulse delay .
- ±10 V output . Short proof
output .
- Paired, Burst, Gated,
Delayed & Un-
delayed pulse
mode ; ±10 V output .
Short-proof output .
Paired and Delayed pulse ; 10 V
output .
Positive and Negative-going
trigger
output signal, 50 ns and 1 V ;
High
Amplitude output, 100
V .
Comparator output can
be alter-
nately chopped to a
reference
voltage .
-
Amplitude range 40 mV to 10 V p-p .
- Frequency range 350 kHz to
100 MHz .
- Frequency range 65 MHz to
500 MHz .
- Marker
outputs, 5 sec to 1 ps .
Sinewave
available at 20, 10,
and 2 ns . Trigger pulses 1, 10,
100 Hz
; 1, 10, and 100 kHz .
Multiple time-marks can
be
generated
simultaneously .
- Marker
outputs, 1, 10, 100, 1000,
and 10,000 ps, plus 10 ns
sinewave .
184 - Marker outputs, 5 sec to 2
ns . Sine-
wave available at 50, 20,
10, 5,
and 2 ns . Separate
trigger pulses
of 1 and .1 sec ; 10, 1, and .1 ms
;
10 and
1 ps . Marker amplifier pro-
vides positive or negative
time
marks of 25 V min . Marker
intervals of
1 and .1 sec ; 10, 1,
and .1
ms ; 10 and 1 /is .
2901 -
Marker outputs, 5 sec to 0 .1 ps .
Sinewave available to 50,
10,
and 5 ns . Separate
trigger pulses,
from 5 sec to 0 .1
ps .
Multiple
time-marks can be gene-
rated simultaneously .
NOTE : All TM 500 generator outputs
are short-proof . All TM 500 plug-in Instruments require TM 500-Series
Power Module .
108 PG 502 - 5 V output
108
111 PG
502 - Risetime less than 1 ns ; 10 ns
111
Pretrigger pulse delay .
114 PG 502 - t5 V output
114
115 PG 502 - Does not have Paired,
Burst, Gated, 115
Delayed
& Undelayed pulse mode ;
Has t5 V output .
2101
PG 502 - Does not have Paired or Delayed 2101
pulse . Has t5 V output .
PG 506 replaces 106 PG 506 -
Positive-going trigger output signal
106
at least 1 V ; High Amplitude out-
put, 60 V .
067-0502-01 PG 506 - Does not have chopped
feature . 0502-01
SG 503 replaces 190,
190A, 190B SG 503 -
Amplitude range 5 mV to 5 .5 V p-p . 190B
191 SG 503 - Frequency range 250 kHz to 250 MHz .
191
067-0532-01 SG 503 - Frequency range 250 kHz
to
250
MHz . 0532-01
TG 501 replaces 180,
180A TG 501 - Marker outputs, 5
sec to 1 ns . 180A
Sinewave available
at 5, 2, and 1 ns .
Trigger
output - slaved to marker
output from 5 sec through 100 ns .
One time-mark can be generated
at a
time .
181 TG 501 - Marker outputs, 5
sec
to
1 ns . Sine- 181
DM 501 replaces
7D13
PG
501 replaces 107 PG 501 - Risetime less than 3 .5 ns
into 107 - Risetime less than 3 .0 ns
into
500 .
50 171 .
108 PG 501 - 5 V output
pulse ; 3 .5 ns Risetime . 108 - 10
V output pulse ; 1 ns Risetime .
111 PG 501
-
Risetime less
than 3 .5 ns ; 8 ns
111 - Risetime 0 .5 ns ; 30 to 250 ns
Pretrigger pulse delay .
Pretrigger Pulse delay .
114 PG 501 - t5 V output .
114 - ±10 V output . Short proof output .
115 PG 501 - Does not have Paired,
Burst, Gated, 115 - Paired, Burst, Gated,
and Delayed
or Delayed pulse mode
; t5 V do pulse mode ;
±10 V output .
Offset . Has t5 V output .
Short-proof output .
PG 502 replaces 107