INSTRUCTION MANUAL Ultra Resolution Day & Night IR Dome Camera Ultra Resolution Day & Night IR Dome Camera P/N 01.BMS.11.0071401 V1.1 Vandal Model: DPV24DL Indoor Model: DPD24DL Please read this manual thoroughly before use and keep it handy for future reference.
-i- -ii-
INTRODUCTION Features All Models Feature: DPD24DL • 1/3” Sony Super HAD™ II CCD • Indoor Dome Model • 2.8-10.5mm Varifocal Day/Night Lens F1.
MEASUREMENTS PACKING CONTENTS 97.0 mm 3.82 in Indoor Dome package contains the following: 55.5 mm 2.19 in 112 mm 4.4 in 3/4’’ -14 NPS thread 40 mm 1.57 in 3.4" 87 mm Ø 0.1" 3.
JUNCTION BOX INSTALLATION TYPES Screws Cable Entry 2S Fitting VANDAL DOME FITTINGS a. 2S Fitting requires only 2pcs of base attachment screws. Note: You have a reduced space in which to hide cables using this type of installation. Recommended for indoor dome only. Note: All plate fittings are put so screw holes show the countersunk cutouts. Camera base mount fits into the Pendant Cap - model # MNTV2XPC Replaces the need for the camera base.
INSTALLATION. VANDAL DOME a) Remove the three tamper screws using the Hex key provided. 1 1 b) Use included mounting template to mark and pre-drill the required holes. Use included 2.8” screws to mount the camera directly to the mounting surface. Proceed to step 4 b 2 INSTALLATION. INTERNAL DOME a or Remove the camera base by unscrewing the base locking screw (indicated with a padlock marking) and turn camera module approx. 5 degrees counter-clockwise to detach camera base from the camera module.
CAMERA ADJUSTMENT CAMERA ADJUSTMENT RCA Service Connector Use supplied RCA - BNC cable If you require BNC output. OSD function joystick. Pressing down on joystick acts as ENTER function. MENU TREE SUMMARY SETUP MENU LANGUAGE LENS WHITE BAL PICT ADJUST NR ENGLISH AUTO ATW NEXT EXIT SAVE ALL AUTO IRIS TYPE MODE SPEED DC AUTO ATW 239 SPEED DELAY CNT 016 ATW FRAME x1.
CAMERA ADJUSTMENT OSD MENU control CAMERA ADJUSTMENT Select the language in which to display the OSD menu. Note: Selection changes the language displayed immediatley. Press down on the function joystick to access the setup menu. • Main setup menu is displayed on the monitor screen. SETUP MENU LANGUAGE: English,Japanese,German, French Russian, Portuguese, Spanish, Chinese.
CAMERA ADJUSTMENT CAMERA ADJUSTMENT WHITE BAL SETUP MENU LANGUAGE LENS WHITE BAL PICT ADJUST NR USER1 WB B-GAIN R-GAIN ENGLISH AUTO ATW White Balance can be set to following: NEXT EXIT ALL ATW / PUSH / SAVE USER1 / USER2 / ANTI CR / MANUAL / PUSH LOCK • RETURN • ATW 029 077 USER2 User defined gain adjustment on B and R USER2 WB B-GAIN R-GAIN ATW 239 SPEED DELAY CNT 016 ATW FRAME x1.
CAMERA ADJUSTMENT CAMERA ADJUSTMENT LEVEL: 000-255 Specifies the R and B gain values for manual WB. The actual variable range is limited to the range from the low color temperature (approx. 1800K) to the high color temperature (approx. 10500K). Default setting is 58 • PUSH LOCK Press down on joystick to set current scene as the white balance level. Use a grey card in front of lens to give a nutural white level.
CAMERA ADJUSTMENT CAMERA ADJUSTMENT •LUMINANCE SETUP MENU BACKLIGHT OFF ATR OFF PRIVACY OFF MOTION DET OFF CAMERA ID OFF SYNC INT CAMERA RESET BACK EXIT BACKLIGHT •CONTRAST PRIVACY OFF / ON Hide an area so that it is not displayed on the monitor.
CAMERA ADJUSTMENT MOTION DET CAMERA ADJUSTMENT OFF / ON BOTTOM: Motion Detection is defined by rectangular areas. This give a visual identification of motion areas. MOTION DET DETECT SENSE BLOCK DISP OFF MOTION AREA ON AREA SEL 1/4 TOP BOTTOM LEFT RIGHT RETURN 111 000 000 000 000 LEFT: RIGHT: Set the bottom side of the monitoring frame selected by the AREA SEL parameter Set the left side of the monitoring frame selected by the AREA SEL parameter.
CAMERA ADJUSTMENT TROUBLE SHOOTING Refer to the following table if you are experiencing trouble with your camera. Contact an authorized technician if the table does not provide you with a solution to the trouble. LL PHASE 326 Nothing appears on the screen. Check that the power cord and line connection between the camera and monitor are connected properly. Check that you have properly connected VIDEO cable to the camera VIDEO output jack. The image on the screen is dim.
