32” HD Ready LCD TV DGL32 User’s Manual
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
10. POWER SOURCES This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions. 11. GROUNDING OR POLARIZATION This unit is equipped with a polarized alternating current line plug (a plug having one blade wider than the other).
TO PREVENT POSSIBLE DANGER, ELECTRIC SHOCK, AND OTHER INJURIES WHEN HANDLING YOUR DISPLAY, PLEASE BE AWARE ALL WARNINGS AND SAFETY PRECAUTIONS CONTAINED AS BELOW. Never Insert anything into DISPLAY!! Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts. Never spill liquid of any kind on the Display。 Do not attempt to service the DISPLAY yourself!! Opening or removing covers may expose you to dangerous voltages and other hazards.
CONFORMITY AND COMPLIANCE FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
Table of contents Introduction Congratulations on the purchase of your LCD TV. This handbook has been designed to help you install and operate your display. We would recommend reading it thoroughly. Table of contents Page Getting Start Features…………………………………………………………. Standard Accessories…………………………………………. Location of Controls.…………………….………………….…… Remote Control………………………………………………….. 6 6 8 10 Installation Installing your Display…………...…………………………….. SET UP………..……………………………………………….
Getting Start FFeeaattuurreess ․ Support WXGA resolution up to 1366x768 pixels ․ Wide viewing angle ․ VESA DPMS-compliant power saving: automatically powers down the monitor after a defined period of inactivity ․ Digital Character Smoothing ․ Analog TV tuner ․ Windows 95/98/2000/XP Plug & Play Compliant ․ Versatile, User friendly OSD ․ Plug & Play: Conform to the VESA standards and support DDC 2B spec.
ANTENNA CONNECTIONS If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV (CATV) see “CABLE TV CONNECTIONS”. Combination VHF/UHF Antenna (Single 75 Ohm cable or twin-lead wire) 300 Ohm Connect the 75 Ohm cable from the combination VHF/UHF antenna to Jack. If your combination VHF/UHF antenna has a 300 Ohm twin-lead wire, the 300-75 Ohm Matching Transformer may be necessary. Connect Ohms cable and UHF 300 Ohm.
Getting Start Front View LLooccaattiioonn ooff C Coonnttrroollss Operating the monitor Multicolor LED indicator illuminates in Green for operating PC monitor and TV system, Red when Power plug in (Standby). Front Panel Buttons： ① POWER：Press to active the Display On and Off (Standby). ② SOURCE：Press to display all of the available input sources. ③ MENU：Press to see OSD menu of your TV’s adjustments / selections. ④ ENTER: Press to confirm selection / adjustment.
Getting Started Rear View REAR PANEL JACKS Side View 1 Y1Cb1Cr1 Connecting to the Video component1 output terminal of the video output device. 2 Y1Cb1Cr1 Audio Audio input terminal connecting to the audio output terminal of the video output device. 3 Y2Pb2Pr2 Connecting to the Video component2 output terminal of the video output device. 4 Y2Pb2Pr2 Audio Audio input terminal connecting to the audio output terminal of the video output device.
Getting Start R Reem moottee C Coonnttrrooll TV Function 1 2 POWER TV 3 SOURCE 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Number keys DISPLAY MUTE MTS SOUND PICTURE SLEEP Enter Recall MENU CH d/c ZOOM VOLe/f PIP Source Position Freeze Swap ENTER C.C. V-Chip Power On/Off Switch source to TV mode. Select main input source: TV VGA AV3 DVI S-VIDEO COMPONENT 1 COMPONENT 2 AV1 AV2 Select channel by numbers. Display current information. Turn speaker On or Off.
REMOTE CONTROL BATTERY INSTALLATION Slide the battery compartment cover. Install two “AAA” batteries (supplied), paying close attention to the + / - polarity diagram in the battery compartment. Replace the compartment cover. BATTERY PRECAUTIONS The precautions below should be followed when using batteries in this device: 1 Use only the size and type of batteries specified. 2 Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Installation IInnssttaallliinngg yyoouurr D Diissppllaayy Step 1. Positioning the display set Place your Display set on a solid stable surface. Do not expose the display to water, or a heat source. Do not obstruct the ventilation grid at rear. ANT Step 2. Connecting the aerials (Antenna) 1. Use the antenna adapter (included) to connect the Cable / Antenna to TV tuner socket situated at the side of the TV. 2. Connect the cable to TV. ① Tuner Adapter ② Aerial / Antenna cable Step 3.
Installation S SE ETT U UP P If TV is connected to an antenna, you’ll need to set a few important items in the menu system the first time you turn on your Display. Auto scan: This part of the setup allows the TV tuner to search for all channels viewable though your antenna or cable TV system (when there is no cable box connected). Press “MENU” on Remote or TV’s front panel to view OSD- “TV Parameters”. Pressf button 3 times to highlight the fifth item “Channel Settings”.
Operation - TV B Baassiicc O Oppeerraattiioonn Power On/Off Press the “POWER” key to turn ON the Display. The power indicator changes from red to green. When the power is OFF (stand by), the power indicator changes from green to red. Source select Press “SOURCE” button to select the input signal.
Operation - TV O OS SD DM ME EN NU UD DE ES SC CR RIIP PTTIIO ON N To access MENU navigate and make adjustments, use MENU, cCH, dCH, eVOL, f VOL and ENTER. Pressing “MENU” display and the OSD menu. Use cCH / dCH on the remote controller to scroll the options on the menu. Press “ENTER” button to enter sub menu. Usee/f to adjust settings. Press “ENTER” to confirm desired settings. Press “MENU” to exit the current OSD menu. Main Menu: There are seven SUB-MENUS in the main OSD Menu; 1.TV PARAMETERS; 2.
Operation - TV TTV V//P PC CP Paarraam meetteerrss TV Parameters Press “MENU” and make sure “TV Parameters” appears on the screen. Adjusting the TV setting: Brightness: Alters the brightness of the image. Contrast: Alters the ratio of light to darkness. Sharpness: Adjusts the sharpness of the color. Saturation: Alters the color saturation. Hue: Alters the color intensity. Color temp: Adjusts the color temperature of the picture. Three options are available here: 6500, 7500, 9300, and USERS.
Operation - TV A Auuddiioo S Seettttiinnggss Press “MENU” and pressf to make sure the “AUDIO SETTINGS” is displayed on the screen. In TV, Video, and PC modes Adjusting the audio setting: MTS (For TV mode only): Volume: This will adjust the level of volume. Mute: Mutes the sound Bass: This will adjust the level of low frequency content in the sound. (enabled only for BBE or SRS WOW feature is off) Treble: This will adjust the level of high frequency content in the sound.
Operation - TV P Piiccttuurree--IInn--P Piiccttuurree PIP function: With PIP function you can watch a multi-screen on the Display at the same time. PIP SOURCE POSITION SWAP Freeze To start the PIP function. Off->PIP(Small) ->PIP(Medium) ->PIP(Large)-> PBP -> POP To select the sub screen’s source. (see the PIP structure below) To adjust the PIP position. To switch the picture of main screen to sub screen. To freeze the PIP main screen.
Operation - TV G Geenneerraall S Seettttiinnggss Press “MENU” and pressf to make sure “GENERAL SETTINGS” appears on the screen. In TV, Video, and PC modes Adjusting the general setting: OSD Timeout: Adjusts the OSD disappearing time without taking any action. Press e/f to increase or decrease the time. Timeout range: 10, 20, and 30 sec. OSD Position: Adjusts the horizontal and vertical position of the OSD on the screen. OSD Language: English, French, Spanish are available. Display Info.
Operation - TV G Geenneerraall S Seettttiinnggss Deinterlace: Note: Only available in AV, S-Video, TV1, Component1 input sources. DCDI: This function produce smooth and natural images Without staircasing or jaggies . CCS: This function (CCS) removes “false color” artifacts. FILM Mode: This function produces artifact-free images by proper handling of 3:2 and 2:2 pulldown materials.
Operation - TV For U.S. area only P Paarreennttaall C Coonnttrroollss Closed caption: Closed caption is a system which allows you to read the voice content of television programs on the TV screen to help the hearing impaired. This feature uses onscreen text boxes to show conversation and dialogue while the program is progress. Usually C.C. 1 is the most used. C.C. 2 may be used for alternate languages.
Operation - TV For U.S. area only P Paarreennttaall C Coonnttrroollss V-chip: The V-chip feature automatically blocks TV programs and movies based on violence, sex, or other content you may believe inappropriate for children. Once you block programs, you can unblock by entering a password. Use remote control: 1. Press “V-Chip” key on the remote controller and the V-Chip OSD will be displayed on the screen. 2.
Operation - TV For U.S. area only P Paarreennttaall C Coonnttrroollss TV PG Rating (Parental Guideline) USA V-chip Rating System V-chip reads the program’s age-based rating. If you have blocked the rating, you will receive a rating message on the screen while you select the blocked program None TV-Y TV-7 TV-G TV-PG TV-14 TV-MA TV P.G. Rating Unblock None All children. None Directed to children 7 years and older. The rating of F. Violence can be blocked General audience.
Other Information TTrroouubblleesshhoooottiinngg Perform the adjustments according to Instruction Manual. If the problem still exists, you cannot correct the problem, stop using the DISPLAY and contact your dealer or the nearest service center for further assistance. SYMPTOMS No picture a) Power indicator does not light up. No picture b) Power indicator is green. No Picture c) Power indicator is red. Unclear picture, Noise No Sound CHECK ITEMS Make sure the power cord is firmly plugged in the socket.
Other Information S Suuppppoorrtteedd O Oppeerraattiioonn M Mooddee Supported Timing: Display Mode VGA 640 x 480 720X400 VESA SVGA 800 x 600 SXGA 1280 x 1024 Analog / Digital Horizontal Frequency Vertical Frequency 31.5 KHz 60 Hz 37.9 KHz 72 Hz 37.5 KHz 75 Hz 43.3 KHz 85 Hz 37.9 KHz 85 Hz 35.1 KHz 56 Hz 37.9 KHz 60 Hz 48.1 KHz 72 Hz 46.9 KHz 75 Hz 53.7KHz 85 Hz 48.4 KHz 60 Hz 56.5 KHz 70 Hz 60.0 KHz 75 Hz 68.7KHz 85 Hz 80.
