Technical information

www.fagerhult.com • www.fagerhult.co.uk482
DMX control using the Philips Colour Chaser Touch pro-
vides many possibilities for personalised programming of
light functions.
The panel can be mounted over a standard pattress or
directly onto a wall. Power supply units could be placed
e.g. above a suspended ceiling.
Installation is simple. Use ordinary network cables
between the control panel and the loads. Connect each
light source or drive unit to a 230 V power supply. Lu-
minaires using DIP-switch addressing can be combined
with luminaires using RDM addressing (via software).
Colour Chaser Touch 86240:
• Touch button for TO/FROM.
• Four saveable presets/light scenes.
• Manual adjustment of colour (C), intensity (I) and
saturation (S).
• Software for advanced lighting setup – RDM address-
ing of light sources
- Simple composition of light sequences using large
number of preset colour themes.
- Colour setup can be sampled from images.
- The Colour Chaser Touch panel can be
connected to a computer via USB.
Philips ToBeTouched is an easy-to-use panel for setting
light and colour. The panel’s intuitive design makes the
functions simple to understand, enabling the desired
light and colour settings to be made.
The panel can be mounted over a standard pattress or
directly onto a wall. Power supply units could be placed
e.g. above a suspended ceiling.
Installation is simple. Use ordinary network cables
between the control panel and the loads. Connect
each light source or drive unit to a 230 V power supply.
Luminaires using DIP-switch addressing can be combined
with luminaires using RDM addressing. All devices will be
adjusted at the same time.
ToBeTouched 86241 (for full colour control):
• Touch button for TO/FROM.
• Two saveable presets.
• Manual adjustment of colour (C), intensity (I) and
saturation (S).
ToBeTouched 86242 (for colour-temperature control):
• Touch button for TO/FROM.
• Two saveable presets.
• Manual adjustment of colour temperature between
2500 and 6500 K.
Control using the Helvar 920 Router. This device has
a connection for DMX control of loads, which can be
combined with DALI control. This enables advanced
RGB control using DMX to be integrated with ordinary
fluorescent tube loads and control functions. DMX
control is normally limited to a single control unit, but
this solution enables all the lighting to be controlled in a
more energy-ecient and user-friendly manner.
• Manual adjustment using touch buttons.
• Sensors for on/o etc.
• Full calendar control. The light can be programmed
in detail according to almanac forecasts and event
calendars.
• Flexible solution for light sources.
DMX (RDM) installation using Philips Colour Chaser Touch
Lexel
Pleiad LED
Wallwasher
Lexel
Pleiad LED
Wallwasher
Lexel
Pleiad LED
Wallwasher
Lexel
Pleiad LED
Wallwasher
Luminaire 1
91081 network cable Cat5 10 m
91080 network cable Cat5 3 m
PSU for panel
and DMX
(included
in Philips
Colour Chaser)
86240
Philips
Colour
Chaser
Touch
Luminaire 2 Luminaire 3 Luminaire 32
end-of-line
resistor
(if applicable)
Lexel drives can be programmed to dierent addresses using the panel software.
DMX-installation using Philips ToBeTouched
Lexel
Pleiad LED
Wallwasher
Lexel
Pleiad LED
Wallwasher
Lexel
Pleiad LED
Wallwasher
Lexel
Pleiad LED
Wallwasher
Luminaire 11
91081 network cable Cat5 10 m 91080 network cable Cat5 3 m
86243
Power Supply
Unit for
panel and
DMX
86241
Philips
ToBeTouched
(RGB)
86242
Philips
ToBeTouched
(colour
temperature)
Luminaire 12 Luminaire 13 Luminaire 132
end-of-line
resistor
(if applicable)
All luminaires are controlled together.
DMX installation using DALI Router 920
Lexel
Pleiad LED
Wallwasher
Lexel
Pleiad LED
Wallwasher
Lexel
Pleiad LED
Wallwasher
Lexel
Pleiad LED
Wallwasher
Luminaire 1
91081 network cable Cat5 10 m 91080 network cable Cat5 3 m
Luminaires with DALI HF ballasts
DALI sensors
DALI touch-button panels
DALI Router 920
Luminaire 2 Luminaire 3 Luminaire 32
end-of-line
resistor (if
applicable)
All Lexel luminaires need to be pre-programmed using, for example,
Philips Colour Chaser software for separate addressing.
Set the address for ordinary DMX luminaires using DIP switches.
Connect DALI devices to the router for e.g. touch-button control.
DMX control
Lexel colour control
For more information go to www.barbourproductsearch.info