Technical information

www.fagerhult.com • www.fagerhult.co.uk476
The e-Sense ActiLume Connection Box was designed particularly
for use in lecture rooms, but equally lends itself to an oce envi-
ronment or rooms where the installation can be hidden above a
suspended ceiling.
The installation and ongoing use of lighting solutions with control
systems can often a complicated process. At an early stage a good
understanding of the features of the control system is vital to avoid
planning mistakes. Time can be needlessly wasted changing the
installation, or simply starting again from the beginning.
As a control system, the e-Sense ActiLume is already prepared
for simple deployment. Minimal eort is required to implement
an installation on site, and changes can easily be made using an IR
transmitter, or simply via a tip of a pen.
To aid the installation turning into a more modern, exible and
quick solution, there is a choice of luminaires ready for connec-
tion to a specially made connection box. With virtually everything
already connected. Connect the power to the box and all luminaires
can then be connected one at a time without needing to discon-
nect the power. This reduces the risk of mixing up the connections,
facilitating a quick, safe installation. All functions can be connected
or disconnected without risk.
For maintenance work, the power does not need to be discon-
nected. The luminaire can simply be disconnected from the box or
splice connection. During maintenance work, the other luminaires
in the room will remain lit to facilitate work. A luminaire can also be
removed and maintenance work carried out elsewhere.
We have chosen the Wieland GST connection system as standard
for this solution.
e-Sense ActiLume Connection Box
Quick connection system for controlling using e-Sense ActiLume
e-Sense ActiLume Connection box
ActiLume Connection Box (complete) 88220
Wieland T-connector 91026
Wieland Connector cable, L= 3.0 m 88222
ActiLume 86152 External sensor 86152
IR transmitter for programming (IRT8099) 86155
Connection box prepared for connection
of master and slave luminaires, etc.
Connectors included for:
Feed 230 V (black).•
Pulse switch (brown).•
Switch (brown).•
External occupancy detector (grey).•
Connection of board illumination •
(5-pole, blue).
Example of Master luminaire for connec-
tion to e-Sense ActiLume Connection Box
DTI 28924-321
DTI Type 2 Beta 2x35 W, with e-Sense
ActiLume sensor and complete cable
rack, screened and halogen-free.
Example of Slave luminaire for connec-
tion to e-Sense ActiLume Connection Box
DTI 28924-325
DTI Type 2 Beta 2x35 W, with complete
cable rack, screened and halogen free.
The advantages of the e-Sense ActiLume
Connection Box
Luminaires complete with all cable •
racks – no knowledge required for con-
necting the parts.
Quick connection in connection box – •
each function clearly marked.
All connectors for external functions •
included with delivery – no knowledge
required for ordering component parts.
Comprehensive installation instructions •
included in the pack.
The control system works immediately •
following power-up.
Easy programming, either directly on •
the master luminaire or using the IR
transmitter.
Control functions
Occupancy detection with a choice of •
automatic or manual switch on.
Adjustment for daylight according to •
pre-set level. Can easily be changed.
Manual control via a momentary •
pushbutton for On/O and adjustment.
Switches o after 15 minutes or •
changes to a lower light level depend-
ing on the choice of “mode”.
Oset function. Luminaires at greater •
distances from windows can be con-
nected to a DALI 2 for 30 % oset. This
means the light is regulated with an
oset of 30 % from the setting on the
master luminaire.
The system is supplied in factory setting
modes 1 and 2. Program using IR trans-
mitter 86155 for a choice of 7 additional
“modes”.
e-Sense ActiLume Connection Box
For more information go to www.barbourproductsearch.info