User Manual
Table Of Contents
- Contents
- Installation QuickStart
- Welcome to 003 and 003 Rack
- Windows Configuration
- Mac Configuration
- Launching and Configuring Pro Tools LE
- 003 Top Panel
- 003 Operating Modes
- 003 Top Panel Overview
- Display Section
- Fader Section
- Console/Channel View Section
- Transport and Navigation Controls
- Automation Section
- Modifiers Section
- Mic/DI Input Controls
- Monitor Section
- 003 Rack Front Panel
- 003 and 003 Rack Back Panels
- Making Studio Connections
- Getting Sound In and Out of Your 003 or 003 Rack
- Connecting a Microphone
- Connecting Instruments to 003 or 003 Rack
- Connecting Equipment with Digital Ins and Outs
- Word Clock
- Using External Effects Devices
- Monitoring and Recording from Alternate Sources
- Recording from a Digital Device
- Connecting a Recorder for Mixdowns
- MIDI Connections
- Common Tasks with Pro Tools LE
- Pro Tools Mode with 003
- Saving a Session
- Working in Console View
- Working in Channel View
- Display Options in Console and Channel View
- Navigating and Editing Values in Entry Fields
- Working with Tracks
- Assigning Pro Tools Paths (Input, Output, Sends, Inserts)
- Working with Output Windows
- Recording
- Navigating in the Edit Window
- General Editing
- Working With Memory Locations
- Controlling Track Display on the Control Surface
- Working with Automation
- 003 Top Panel Shortcuts
- Configuring MIDI Studio Setup (Windows Only)
- Configuring AMS (Mac OS X Only)
- Utility Mode (003 Only)
- Hard Drive Configuration and Maintenance
- Troubleshooting
Chapter 11: Pro Tools Mode with 003 89
3 Press the Channel Select switch under a
plug-in name.
4 Press the Plug-In Master Bypass switch.
To bypass all plug-ins on a channel:
1 Press the Insert switch (Channel View section)
to put 003 in Channel View.
2 Press a lit Channel Select switch to display the
inserts for the corresponding track.
3 Press the Plug-In Master Bypass switch.
In mixed mode situations, where some plug-ins
are bypassed and some are not, pressing the
Master Bypass switch changes all plug-ins to by-
passed. Press Master Bypass again to take all
plug-ins out of bypass.
Pan/Send Workflows in Channel
View
When the Pan/Send switch is enabled (lit), 003
identifies channels with sends assigned to them
by illuminating their Channel Select switches. If
no sends are present for the current bank of
channels, no Channel Select switches will be lit.
In this view, you can display sends, adjust send
levels, and toggle pre- and post-fader operation.
To display the sends on a track:
1 Press the Pan/Send switch to put 003 in Chan-
nel View.
2 Press a lit Channel Select switch.
3 Do one of the following:
• To display Sends A–E, press the Left Page
switch.
• To display Sends F–J, press the Right Page
switch.
The LCD display for the first channel strip
shows track pan position for that track. (If the
track is a stereo track, you can toggle between
left and right pan by pressing the Meter switch
immediately to the right of the rotary encoders.)
The LCD display for channels 3–7 shows the
send names. Their rotary encoders control the
levels for the corresponding send.
The Channel Select switches on channels 3–7
toggle pre- and post-fader metering for the cor-
responding send.
To adjust send levels for any of the sends on a
single track:
1 Press the Pan/Send switch in the Channel
View switch section.
2 Press the Channel Select switch for the track
with sends you want to view.
3 Adjust a channel’s send level by turning its ro-
tary encoder.
To adjust pan levels on a track that has sends:
1 Press the Pan/Send switch in the Channel
View switch section.
2 Press the Channel Select switch for the track
with sends that has panning you want to adjust.
3 Do one of the following:
• If the track is a stereo track, toggle the
Meter switch to Left or Right.
– or –
• If the track is a mono track, toggle the
Meter switch to Left.
Hardware I/O inserts cannot be bypassed in
Pro Tools, so the Plug-in Master Bypass
switch has no effect on them.