User Manual
Table Of Contents
- Contents
- Installation QuickStart
- Welcome to 003 and 003 Rack
- Windows Configuration
- Mac Configuration
- Launching and Configuring Pro Tools LE
- 003 Top Panel
- 003 Operating Modes
- 003 Top Panel Overview
- Display Section
- Fader Section
- Console/Channel View Section
- Transport and Navigation Controls
- Automation Section
- Modifiers Section
- Mic/DI Input Controls
- Monitor Section
- 003 Rack Front Panel
- 003 and 003 Rack Back Panels
- Making Studio Connections
- Getting Sound In and Out of Your 003 or 003 Rack
- Connecting a Microphone
- Connecting Instruments to 003 or 003 Rack
- Connecting Equipment with Digital Ins and Outs
- Word Clock
- Using External Effects Devices
- Monitoring and Recording from Alternate Sources
- Recording from a Digital Device
- Connecting a Recorder for Mixdowns
- MIDI Connections
- Common Tasks with Pro Tools LE
- Pro Tools Mode with 003
- Saving a Session
- Working in Console View
- Working in Channel View
- Display Options in Console and Channel View
- Navigating and Editing Values in Entry Fields
- Working with Tracks
- Assigning Pro Tools Paths (Input, Output, Sends, Inserts)
- Working with Output Windows
- Recording
- Navigating in the Edit Window
- General Editing
- Working With Memory Locations
- Controlling Track Display on the Control Surface
- Working with Automation
- 003 Top Panel Shortcuts
- Configuring MIDI Studio Setup (Windows Only)
- Configuring AMS (Mac OS X Only)
- Utility Mode (003 Only)
- Hard Drive Configuration and Maintenance
- Troubleshooting
003 & 003 Rack Getting Started Guide86
To toggle a send between pre- and post-fader
operation:
1 Press the Send switch to put 003 in Send View.
2 Press the Channel Select switch under a send
name to toggle its pre- and post-fader setting.
Insert View Workflows
When the Insert switch is enabled (lit), 003 is in
Insert View. In this view, the LCD shows the
names of currently-assigned inserts (hardware
inserts or plug-ins) across all channel strips for a
given insert position (Inserts A–E in Pro Tools).
If a hardware insert or plug-in is selected in
Pro Tools, its name flashes in the LCD.
In this view, you can display inserts, plug-in
controls, bypass plug-ins, and assign inserts in
Assign mode.
Working with Inserts
To display the inserts on an Insert position (A– E):
1 Press the Insert switch (Console View section)
to put 003 in Insert View.
2 Press the corresponding Insert/Send Position
switch A–E.
The names of all inserts on that track are dis-
played in the LCD. (While the names of hard-
ware I/O inserts are displayed, they have no ed-
itable parameters, so the Channel Select
switches and the rotary encoders have no effect
on them.)
To display the controls for a plug-in:
1 Press the Insert switch (Console View section)
to put 003 in Insert View.
2 Press the corresponding Insert/Send Position
switch A–E.
3 Press the Channel Select switch under a
plug-in name.
003 goes into Channel View and displays the
plug-in’s controls across all channel strips. Con-
trols are assigned to the rotary encoders.
Switched controls (such as Master Bypass or
Phase Invert) are controlled by Channel Select
switches.
4 To display additional pages of plug-in controls
(if any), press the Left and Right Page switches.
To bypass a plug-in:
1 Press the Insert switch (Console View section)
to put 003 in Insert View.
2 Hold Command/Ctrl and press the Channel
Select switch under the plug-in name.
The LCD screen displays the name of bypassed
plug-ins in all capital letters.
For information on assigning inserts in As-
sign mode, see “Assigning Pro Tools Paths
(Input, Output, Sends, Inserts)” on page 92.
The Left or Right Page switch flashes when
an additional page is available.