User Manual
Table Of Contents
- Contents
- Installation QuickStart
- Welcome to 003 and 003 Rack
- Windows Configuration
- Mac Configuration
- Launching and Configuring Pro Tools LE
- 003 Top Panel
- 003 Operating Modes
- 003 Top Panel Overview
- Display Section
- Fader Section
- Console/Channel View Section
- Transport and Navigation Controls
- Automation Section
- Modifiers Section
- Mic/DI Input Controls
- Monitor Section
- 003 Rack Front Panel
- 003 and 003 Rack Back Panels
- Making Studio Connections
- Getting Sound In and Out of Your 003 or 003 Rack
- Connecting a Microphone
- Connecting Instruments to 003 or 003 Rack
- Connecting Equipment with Digital Ins and Outs
- Word Clock
- Using External Effects Devices
- Monitoring and Recording from Alternate Sources
- Recording from a Digital Device
- Connecting a Recorder for Mixdowns
- MIDI Connections
- Common Tasks with Pro Tools LE
- Pro Tools Mode with 003
- Saving a Session
- Working in Console View
- Working in Channel View
- Display Options in Console and Channel View
- Navigating and Editing Values in Entry Fields
- Working with Tracks
- Assigning Pro Tools Paths (Input, Output, Sends, Inserts)
- Working with Output Windows
- Recording
- Navigating in the Edit Window
- General Editing
- Working With Memory Locations
- Controlling Track Display on the Control Surface
- Working with Automation
- 003 Top Panel Shortcuts
- Configuring MIDI Studio Setup (Windows Only)
- Configuring AMS (Mac OS X Only)
- Utility Mode (003 Only)
- Hard Drive Configuration and Maintenance
- Troubleshooting
003 & 003 Rack Getting Started Guide10
4 Under Device Manager, choose Device Man-
ager.
5 In the Device Manager window, double-click
IDE ATA/ATAPI controllers, then double-click
the Primary IDE Channel for your IDE hard
drive.
6 Click the Advanced Settings tab.
7 For each device, set the Transfer Mode to
“DMA if available,” and click OK.
8 Repeat steps 5–7 for any additional IDE Chan-
nels.
9 Close the Computer Management window.
Disabling System Standby and Power
Management
When using Pro Tools, the Windows System
Standby power scheme must be set to Always
On. This helps prevent long record or playback
passes from stopping due to system resources
powering down.
To configure Windows Power Management:
1 Choose Start > Control Panel.
2 Double-click Power Options.
3 Click the Power Schemes tab.
4 From the Power Schemes pop-up menu, select
Always On.
5 Click OK.
This sets System Standby, System Hibernate,
and “Turn off hard disks” to Never.
Disabling ClearType Font Smoothing
When using Pro Tools, the Effects “Clear Type”
setting must be disabled.
To disable ClearType font smoothing:
1 Choose Start > Control Panel.
2 Double-click Display.
3 Click the Appearance tab.
4 Click Effects.
5 Deselect “Use the following method to
smooth edges of screen fonts.”
6 Click OK to save your settings and close the Ef-
fects dialog.
7 Click OK.
8 Restart the computer.
Recommended Optimizations
Pro Tools can also be affected by other software
and hardware drivers installed on your com-
puter. For best possible performance, it is recom-
mended (but not required) that you do the fol-
lowing:
• Avoid running any unneeded programs at
the same time as Pro Tools.
• Turn off any software utilities that run in
the background, such as Windows Messen-
ger, calendars, and disk maintenance pro-
grams.
• Turn off any non-essential USB devices
while running Pro Tools.
• If your video display card supports it, en-
able Bus Mastering in the manufacturer’s
Control Panel. See the manufacturer’s in-
structions for details.
On AMD processors, be sure to check and
disable Cool N’Quiet in the System BIOS (in
the Cool & Quiet Configuration section). See
the manufacturer’s documentation for in-
structions on disabling this power option, if
necessary.