User guide

depressed (for more information on monitor mode, refer to page 40 of your "Getting Started with Digi 001" Manual).
If the I/O labels on your track I/O buttons do not match your Digi 001 interface or specify "no interface", you need
to set your I/O setups dialog to the factory default. Go to Setups > I/O Setup and choose the Input tab. Click on
the Default button to reset your inputs to their factory designation. Continue through the Outputs, Insert and Bus
tabs and click the Default button on each page.
Digi 001 Mac Index | All FAQ Index
[5831]
Why does my Pro Tools LE session clip when I open it on TDM hardware?
Pro Tools LE uses the power of your CPU's processor to perform mixing and processing. A side benefit of this
technology is its ability to use 32-bit floating point math to scale the level of signals to avoid clipping (which
translates to great headroom). Signals in Pro Tools LE can indeed clip, but signal management can be easier... you
mostly have to watch output levels for mixed signal busses and bring them down so that they don't clip.
Pro Tools TDM systems use HW DSP acceleration that utilize 24-bit fixed point math. (Comparing 24-bit fixed point
and 32-bit floating point audio systems is a bit like comparing PowerPC and Intel Pentium processors... properly
implemented and designed, you can get a great result out of either one... but comparing the techniques used
directly can be difficult!) TDM systems provide 48 bits of precision at the mix bus, which allows a very large degree
of headroom as well. However, Plug-In processing in the TDM world is restricted to a 24-bit data path, so as with
most any signal processing in the audio world, some attention to level setting is necessary to avoid clipping.
For example , if you introduce a signal into a DigiRack EQ that is close to "full code" (the hottest digital level before
clipping) and you add a large boost on an EQ, you will likely clip the EQ Plug-In. Just as with any rack mounted
device, etc., you can avoid this simply by using the input attenuator control provided. The EQ Plug-In for Pro Tools
LE behaves the same way, but because all of the processing is occurring in the host computer, the levels can be
scaled for you to avoid most clipping without adjustment (other than mix outputs which require it).
Note: Some Plug-Ins use a technique called "double precision arithmetic" to provide 48 bit precision when
processing, which results in increased headroom. This is great, but keep in mind that these Plug-In do require
roughly twice as much DSP power to do their work.
Because of these differences, if you plan on exchanging sessions between Pro Tools LE and TDM systems, it can be
prudent to attenuate the input level of a Plug-In like DigiRack EQ if you have applied a large amount of boost to a
predominant frequency (like a big booming kick drum). This will avoid the possibility of clipping in the TDM version
of the Plug-In, and you'll still get to take advantage of a "24-bit clean signal" when levels are set correctly.
Digi 001 Mac Index | All FAQ Index
[5235]
My D-Verb plug-in is not functioning properly after installing Pro Tools LE 5.1 Mac. D-Verb asks for a key
disk authorization, and I only have a serial number. Do I need a key disk?
WARNING: FREE D-Verb does not work with Pro Tools FREE.
Installing Pro Tools LE 5.1 or the D-Verb Plug-In Demo over previous installs of Pro Tools LE will remove your FREE
D-Verb Plug-In. To keep your FREE D-Verb Plug-in from being overwritten by the Pro Tools LE 5.1 and D-Verb
Demo Installers, remove both the D-Verb and D-Verb AS Plug-Ins from your Plug-Ins folder.Place the plug-ins in a
temporary location other than the Pro Tools Plug-Ins folder and outside of your System Folder, such as on your
Desktop. The Plug-Ins folder is located in the following directory:System Folder:DAE Folder:Plug-Ins
After removing the D-Verb & D-Verb AS Plug-Ins from the Plug-Ins folder,run the Pro Tools 5.1 LE Installer. Once
the Pro Tools 5.1 installation is complete, both the D-Verb and D-Verb AS Plug-Ins can be returned to the Plug-Ins
folder. An updated FREE D-Verb Installer for Pro Tools LE users is posted on the Digidesign website in Support/
Downloads at http://www.digidesign.com/download
Note: If you have already run either the Pro Tools LE 5.1 or D-Verb Demo Installer and fear you have overwritten
your FREE D-Verb Plug-Ins,you can still reinstall the FREE D-Verb Plug-In Promotion from the Pro Tools LE 5.0.1
Software CD.
If you continue to have problems with your D-Verb authorization, download D-Verb v1.8.1 from http://www.
digidesign.com/download/dverb. This version of D-Verb (v1.8.1) does not require authorization.