Brochure

Processing Channel Specification
Input
Name User-Defined
Channel Selection Mono / Stereo
Input Routing Main Input
Analogue Gain -20 to +60dB
Phase Normal / Reverse
Digital Trim 40 to +40dB
Delay 0 - 682ms
DiGiTuBe Drive 0.01 - 50.0
Bias 0 - 6
LPF 20 – 20kHz, 24dB/Oct
HPF 20 – 20kHz, 24dB/Oct
Insert A (Pre EQ/Dyn) On/Off
Equalisation 4 Band EQ: Parametric or
Dynamic (Low/Lowshelf,
Lower-Mid/Lowshelf, Upper-
Mid/
Hishelf, Hi/Hishelf)
On/Off
Freq; 20 – 20kHz
Gain; +/- 18dB
Q: 0.1 -20 (Parametric) / 0.10-
0.90 (Shelf)
Dynamic EQ On/Off
Over/Under
Band On/Off
Threshold; -60 – 0dB
Attack; 0.5ms – 100ms
Release; 10ms – 10s
Ratio; 1:1 – 10:1
Dynamics 1 Single or 4 x Multiband
(3-Band)
Compressor On/Off
Threshold; -60 – 0dB
Attack; 500us – 100ms
Release; 5ms – 5s
Ratio; 1:1 – 50:1
Gain; 0 to +40dB
Hi Crossover; 20Hz – 20kHz
Lo Crossover; 20Hz – 20kHz
Knee : Hard, Med, Soft
Dynamics 2 On/Off
Gate / Ducker Threshold; -60 – 0dB
Attack; 50us – 100ms
Hold; 2ms – 2s
Release; 5ms – 5s
Range; 0 - 90dB
Key; Any Source
Key Listen
Freq/Width; 20 – 20kHz
Compressor On/Off
Threshold; -60 – 0dB
Attack; 500us – 100ms
Release; 5ms – 5s
Ratio; 1:1 – 50:1
Gain; 0 to +40dB
Link; Any Channel / Buss
S/C Source : Any Source
S/C Listen : On/Off
S/C Filter Freq/Width: 20Hz
– 20kHz
Insert B (Post EQ/Dyn) On/Off
Mute Channel Mute
Solo Solo Buss 1 / Solo Buss 2 /
Both,
Channel Safe Socket Properties, Input
Route, Mono/Stereo, Label,
Filters, Trim, Delay, Tube,
Insert A, EQ, Dyn1, Dyn2,
Insert B, Aux, Group Assigns,
Pan, Fade, Mute, Direct Outs,
Full Safe
Output Routing Buss, Insert A, Insert B,
Direct: Pre-Mute / Pre-Fade /
Post-Fade
Fader 100mm Motorised Fader ∞ to
+10dB
Processing Channel Specification
Aux / Group / Matrix Output
Name User-Defined
Phase Normal / Reverse
Digital Trim -40 to +40dB
Delay 0 - 682ms
DiGiTuBe Drive 0.01 - 50.0
Bias 0 - 6
LPF 20 – 20kHz, 24dB / Oct
HPF 20 – 20kHz, 24dB / Oct
Insert A (Pre EQ/Dyn) On/Off
Equalisation 4 Band EQ: Parametric or
Dynamic (Low/Lowshelf,
Lower-Mid/Lowshelf, Upper-
Mid/Hishelf, Hi/Hishelf)
On/Off
Freq; 20 – 20kHz
Gain; +/- 18dB
Q: 0.1 -20 (Parametric) / 0.10-
0.90 (Shelf)
Dynamic EQ On/Off
Over/Under
Band On/Off
Threshold; -60 – 0dB
Attack; 0.5ms – 100ms
Release; 10ms – 10s
Ratio; 1:1 – 10:1
Dynamics 1 Single or 4 x Multiband
(3-band)
Compressor On/Off
Threshold; -60 – 0dB
Attack; 500us – 100ms
Release; 5ms – 5s
Ratio; 1:1 – 50:1
Gain; 0 to +40dB
Hi Crossover; 20Hz – 20kHz
Lo Crossover; 20Hz – 20kHz
Knee : Hard, Med, Soft
Dynamics 2 On/Off
Gate / Ducker Threshold; -60 – 0dB
Attack; 50us – 100ms
Hold; 2ms – 2s
Release; 5ms – 5s
Range; 0 - 90dB
Key; Any Source
Key Listen
Freq/Width; 20 – 20kHz
Compressor On/Off
Threshold; -60 – 0dB
Attack; 500us – 100ms
Release; 5ms – 5s
Ratio; 1:1 – 50:1
Gain; 0 to +40dB
Link; Any Channel/Buss
S/C Source : Any source
S/C Listen : On/Off
S/C Filter Freq/Width: 20Hz
– 20kHz
Insert B (Post EQ/Dyn) On/Off
Mute Channel Mute
Solo Solo Buss 1 / Solo Buss 2 /
Both,
Channel Safe Mono/Stereo, Bus Mode,
Label, Filters, Trim, Delay,
Tube, Insert A, EQ, Dyn1,
Dyn2, Insert B, Group
Assigns, Fade, Mute, Direct
Outs,
Full Safe
Output Routing Outputs, Insert A, Insert B
Fader 100mm Motorised Fader ∞ to
+ 10dB
Audio
Specification
Sample Rate 48kHz, 96kHz
Processing Delay 2ms Typical @ 48k
(60 Stereo Channels,
Stage Input Through
L-R Buss to
Stage Output)
1.1ms @ 96kHz
Internal Processing Up to 40-bit,
Floating Point
A>D & D>A 24-bit Converter
Bit Depth
Frequency Response +/- 0.6dB
(20Hz – 20kHz)
THD <0.05% @ Unity Gain,
10dB Input @ 1kHz
Channel Seperation Better Than 90dB
(40Hz – 15kHz)
Residual Output <90dBu Typical
Noise (20Hz - 20kHz)
Microphone Input Better Than -126dB
Equivalent Noise
Max Output Level +22dBu
Max Input Level +22dBu