Bluetooth Development Kit User’s Guide 94001480000 Rev. 2.
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages.
Contents Chapter 1 Introduction 1.1 1.2 1.3 1.4 1.5 1.6 About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additional Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Downloads and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.4.7 4.4.8 4.5 CODEC Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Reference Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Chapter 5 Limitations 5.1 USB Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 Introduction NOTE: Users are not permitted to make changes or modify the device in any way. With the Development Kit for the Bluetooth Platform Solution from Motorola, the company is launching a unique demonstration and development tool for its platform.
Introduction The following is an overview of the various sections of this user’s guide and a brief description of each section: • Chapter 1, “Introduction” contains an overview of the user’s guide and additional documents available from the CD. The introduction is also where to find information on support, unpacking, system requirements, and a list of the acronyms used in this guide.
Downloads and Support — Enhancing ISM Band Performance Using Adaptive Frequency Hopping • Product Errata • Data sheets and information for components on the Development Kit: — CODEC — USB — UART Level Converter — EEPROMs — Crystals • Bluetooth Core Specification v1.1 1.3 Downloads and Support For Development Kit software and documentation downloads, go to the following website: http://www.btpo.net In addition, you may find useful information on the following websites: http://www.motorola.
Introduction 1.6 Acronyms and Abbreviations Throughout this guide, the following acronyms and abbreviations are used: EEPROM Electrically Erasable/Programmable Read Only Memory Rx Receive(r) SEEPROM Serial Electrically Erasable/Programmable Read Only Memory SPI Serial Peripheral Interface The SPI Bus made by Motorola handles all serial communication with a number of different RF front ends and SEEPROMs.
Chapter 2 Product Overview This section contains a brief overview of the Development Kit. More detailed information on the various elements of the Development Kit is included in later sections and in the separate user’s guides included on the CD. 2.1 Block Diagram The following figure shows the Development Kit block diagram: Figure 2-1. Block Diagram USB USB RS232 RS232 Level Shifter MC71000 MC13180 UART Modular Jack DC Power Input 2.
Product Overview NOTE: The UART and RS232 interfaces cannot operate simultaneously. • USB interface: Full speed (12 Mbit/s) USB node device, HCI USB transport layer, 3.3 V operation, self-powered, National USBN9604 USB controller. The following list shows the USB limitations: — USB interface is for evaluation purposes and only included for ease of use. — Supports OpenUSBDI-compatible USB controllers. USB v1.1. — Does not support Open HCI. — Production release of the MC71000 will not support USB. • 2.
Software Tools 2.5.1 Bluetooth HCI Terminal With the Bluetooth HCI Terminal you can interact with your Bluetooth hardware. The interface is similar to that of an AT Terminal application when communicating with a modem. The Bluetooth HCI Terminal makes it easy to send HCI commands from a computer to a Bluetooth device. Likewise, it is easy to receive HCI responses from a Bluetooth device. Consequently, you can get hands-on experience with the HCI. Or you can test your own Bluetooth hardware.
Product Overview 2-8 Development Platform Kit User Guide Motorola Confidential Proprietary, NDA Required / Preliminary MOTOROLA
Chapter 3 Setup This section provides instructions for setting up the Development Kit hardware and software. 3.1 Setting Up Board To get the board up and running, do the following: 1. Connect the board and PC via the UART (RS232) cable. NOTE: The first time you start up the board, you can only run UART, not USB. 2. Attach power supply to DC connector on board and connect to main electricity supply. 3. Insert the CD in the CD-ROM drive of your PC and follow the onscreen instructions. 3.
Setup 5. Within the Configuration Manager, go to Settings>Com Port and select the USB option. 6. Follow the instructions on screen to disconnect the UART (RS232) cable and connect the USB cable.
Chapter 4 Hardware This section provides information on various aspects of the Development Kit hardware. In addition, Appendix A, “Board Diagram“, contains a diagram of the Development Kit board. 4.
Hardware The reset switch can be activated to re-initialize the entire system. Four buttons are provided for embedded applications: • Volume up • Volume down • Function 1 (connection etc.) • Function 2 (this is an extra button) Seven status LEDs are provided: • Two application-specific LEDs • Class 2 • 24 MHz/32 kHz • RX/TX • Power on • Diversity (shows which antenna is being used) 4.
Electrical • Audio input: 65m Vpp • Audio output: 1.6 Vpp, modular jack 4/4 connector The following table shows the current consumption measurements of the circuits of the MC71000 Bluetooth Baseband Controller and MC13180 Bluetooth Low Power Wireless Data Transceiver ICs. Table 1: Current Consumption Measurements of MC71000 and MC13180 Circuits DH5 asymmetric RX 50.4 mA DH5 asymmetric TX 48.5 mA DH5 symmetric 45.8 mA TX rate 57.6 kbits RX rate 723.2 kbits TX rate 723.2 kbits RX rate 57.
Hardware 4.4.4 Memory The MC71000 has embedded memory of 256 Kbytes of ROM and 64 K of RAM. An image can be uploaded from a host system, or a low-cost serial EEPROM (four-wire connection). For more information on the contents and structure of the MC71000 memory, please refer to the Bluetooth Platform Solution Embedded System User’s Guide. This is accessible from the document overview on the Development Kit CD. 4.4.5 UART Interface The UART interface is embedded in the MC71000.
Chapter 5 Limitations This section deals with the known limitations of the Bluetooth Development Kit. 5.1 USB Limitations The Bluetooth Development Kit has the following USB limitations: • The USB interface is for evaluation purposes only. It is only included for the purpose of showing full bandwidth. • Supports OpenUSBDI-compatible USB controllers. USB V1.1. • Does NOT support Open HCI. • No USB logo certification. • MC71000 does NOT support USB.
Limitations 5-16 Development Platform Kit User Guide Motorola Confidential Proprietary, NDA Required / Preliminary MOTOROLA
Chapter 6 Regulatory This section contains regulatory statements, a list of the countries where the Development Kit will be type approved, and information on what is needed by developers to obtain type approvals for their products. This device is intended for evaluation and development purposes by professionals only and is NOT for re-sale. 6.1 Regulatory Statements NOTE: Users are not permitted to make changes or modify the system in any way.
Regulatory 6.1.5 United States of America and Canada Tested to comply with FCC Standards FOR HOME OR OFFICE USE. See FCC 47CFR part 15.19(b)(2) This device complies with part 15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See FCC regulation CFR47 sec. 15.19(3).
Regulatory Statements 6.1.8 Brazil Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. 6.1.
Regulatory 6.2 Obtaining Type Approvals Customers of Motorola Bluetooth chipsets will face some Bluetooth qualification and regulatory requirements for their products. The following lists the requirements for the major markets as defined by Digianswer/Motorola as tier 1 countries: Australia, Canada, Europe (15 + 4 EFTA countries), Japan, New Zealand and US. A number of other countries worldwide will accept the test reports made for Europe and/or US approvals.
Obtaining Type Approvals FCC testing can be avoided for regulatory purposes for radio modules, provided no changes are made to the radio module BOM or layout, it will still be necessary to perform the Out-of-Band Spurious Emissions-radiated-test of part 15.209. The product might be subject to additional product specific regulations, such as PSTN regulations and other. Type approval applications have to be filed to the national authorities for each product.
Regulatory 6-22 Development Platform Kit User Guide Motorola Confidential Proprietary, NDA Required / Preliminary MOTOROLA
Appendix A Board Diagram The following pages show a diagram of the Development Kit board.
HVDD1V85 C100 100nF HVDD1V85 TRST TDI TMS TCK RTCK TDO JTAG_RESET Sheet 2 32kHz_OSC REFCLK TRST REFCTRL TDI TMS BT[1..9] TCK RTCK DIVERSITY TDO JTAG_RESET REFCLK REFCTRL BT[1..9] DIVERSITY CS0 OE WE SSI[0..4] UART[0..3] 0dBm/20dBm RxTx_SW Sheet 4 REFCLK REFCTRL BT[1..9] DIVERSITY 0dBm/20dBm RxTx_SW RF Front Sheet 3 Ri TXD RTS RXD CTS RxTx_SW 0dBm/20dBm DIVERSITY REFCTRL BT_WAKEUP BT[1..9] CS0 OE WE SSI[0..4] UART[0..
MAIN+ MAIN- J200 3p COT201 Track in PCB R242 7.5R C207 3 2 1 1 R231 2 500mA C205 6.8µF R206 10K TP207 3 8 24 23 21 16 6 10 11 12 18 17 IC202 C203 100µF VCC1 VCC2 Vin+ VinHysteresisSelect Shutdown S INV Q1_b Q2 S OR 1V85_ENABLE 2V65_ENABLE VCC D203 Green LED TP224 REFOUT Detect RESET_b DelayCap OUT1V85 OUT2V65 5 EP AGND1 AGND2 SGND OUT3V0/3V3 R203 1.0K 3V0/3V3 sel 3V0/3V3 ENABLE OUT 4 2 2 15 22 9 19 1 7 4 20 5 EP C206 100nF C208 100nF RESET TP203 1.
TP302 TP313 UART3 TP308 SPI02 SSI3 TP303 TP309 SPI03 SSI4 TP304 33pF C325 CS0 OE WE 22pF SPI00 SPI01 SPI02 SPI03 SPI0[0..
BT2 TP401 BT[1..9] REFCTRL REFCLK BT5 TP404 BT6 TP405 BT1 BT2 BT3 BT4 BT7 BT6 BT5 R401 100R C416 AVcc C415 1µF C423 100nF VCC_RF C418 15pF 1.5nF C438 1.0pF C421 15pF BT[1..
A-6 Development Platform Kit User Guide Motorola Confidential Proprietary, NDA Required / Preliminary MOTOROLA