Specifications
Wavespeed/S Configuration Guide (90000407 Rev. C) – Page 10
Federal Communications Commission (FCC)
Regulatory Information (USA only)
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment gener-
ates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the
receiver.
Connect the equipment into an outlet that is on a circuit
different from the receiver.
Consult the dealer or an experienced radio/TV techni-
cian for help.
Warning: The connection of a non-shielded interface
cable to this equipment will invalidate the FCC
Certification for this device.
This equipment has been certified to comply with the
limits for a class B computing device, pursuant to FCC
Rules. In order to maintain compliance with FCC regu-
lations, shielded cables must be used with this equip-
ment. Operation with non-approved equipment or un-
shielded cables is likely to result in interference to radio
and TV reception. The user is cautioned that changes
and modifications made to the equipment without the
approval of manufacturer could void the user's authority
to operate this equipment.
FCC Regulation - Part 15 Declaration of Con-
formity (DoC)
FCC ID Q4W55M1073-01 or Q4W55M1074-01
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful
interference and
2. This device must accept any
interference received, including
interference that may cause undesired
operation.
This product contains either a class 1 or class 2 Blue-
tooth transceiver board (part numbers 55001073 and
55001074 respectively). The following statement refers
to this board.
IMPORTANT NOTICE: To comply with the FCC RF
Exposure compliance requirements, the following an-
tenna installation and device operating configurations
must be satisfied.
The antenna(s) used for this transmitter must be in-
stalled to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operat-
ing in conjunction with any other antenna or transmit-
ter.
European Community - CE Mark
Declaration of Conformity (DOC)
According to ISO/IEC Guide 22 and EN 45014
Manufacturer’s Name:
Digi International
Manufacturer’s Addr.:
11001 Bren Road East
Minnetonka, MN 55343
declares that the product
Product Name:
Wavespeed/S
Model Number(s):
North America International
301-1121-01 301-2121-01
301-1122-01 301-2122-01
301-1123-01 301-2123-01
301-1124-01 301-2124-01
Product Options: All
conforms to the relevant EU Directives listed here:
EMC Directive 89/336/EEC |
Low Voltage Directive 73/23/EEC
Amending Directive 93/68 EEC
using the relevant section of the following EU standards
and other normative documents:
Safety: IEC 950:1991 +A1, A2, A3, A4
EN 60950: 1992 + A1, A2, A3, A4
EMC
The following summarizes the specifications and
requirements for EN55024:1998, EN55022:1998 Class
B & CISPR 22 Class B emission and immunity tests
and the EN61000-3-2(2000), EN61000-3-3(1995)
current harmonics and voltage variation tests. Actual
test levels are listed in the appropriate tables.