T r a n s P o r t ®D R 6 4 Wireless Routers Installation Guide June 11, 2011
TransPort® DR64 Installation Guide TransPort® DR64 Installation Guide Disclaimer Special notes on safety for wireless routers Digi International makes no representations or warranties with respect to the contents or use of this manual, any software drivers or associated application software provided with this product and specifically disclaims any expressed or implied warranties of merchantability or fitness for any particular purpose.
TransPort® DR64 Installation Guide Table of Contents TransPort® DR64 Installation Guide 1 Package Contents 1 Package Contents ......................................................................5 TransPort DR64 2 Introduction ................................................................................6 Wireless Routers 2.1 Front Panel Features ........................................................................................7 Installation Guide 2.2 Rear Panel Features ..................
TransPort® DR64 Installation Guide TransPort® DR64 Installation Guide 2.1 Preface This guide describes the installation procedure for the TransPort DR family of routers. It is intended to provide sufficient information to be able to connect the unit to terminal equipment and power-on the unit. A complete reference guide to the software features that are available on the product is available separately in PDF format and can be downloaded from the Digi International web site (www.digi.com).
TransPort® DR64 Installation Guide 2.2 TransPort® DR64 Installation Guide Rear Panel Features 2.3 2 1 WIFI SECONDARY 3 WWAN SECONDARY Under Unit Features 4 WIFI PRIMARY [Front of Unit] WWAN PRIMARY 2 DSL 5 LAN3 LAN2 LAN1 LAN0 6 SERIAL 0 PSTN/ISDN 12VDC 1.0A MAX 7 8 9 1. Secondary Wi-Fi (WLAN) Antenna Connector (Wi-Fi models only) - This SMA male connector is used to connect the unit’s secondary Wi-Fi antenna. 1 1 2.
TransPort® DR64 Installation Guide TransPort® DR64 Installation Guide 3 Installation Mounting Tips The TransPort DR64 should be positioned on a flat, level surface or via a wall-mount, rackmount, or DIN rail mounting brackets (see the Accessories section on page 20 for all options). The unit is designed for indoor use and should be mounted in a location with adequate ventilation. Also, do not expose the unit to extremes of heat or cold, strong magnetic fields, or liquids.
TransPort® DR64 Installation Guide 4 Configuration TransPort® DR64 Installation Guide Step 2) Configure the Unit: The easiest way to perform the initial configuration of the unit is by using the Quick Start Wizard. This wizard allows you to configure the following items where applicable: Once the unit has been installed and powered up, it needs to be configured to communicate with the LAN and WAN. Configuration is performed either using the Command Line Interface (CLI) or the Web Interface.
TransPort® DR64 Installation Guide 4.2.1 Cellular: CDMA TransPort® DR64 Installation Guide 4.2.1.2 If your unit is to be used on a CDMA network, the embedded module must be provisioned on the network before it can make a connection. Note: If your unit uses a Gobi module (indicated by a model number of DR64-U5xx-xxx-xx), and you did not select the appropriate CDMA carrier via the Quick Start Wizard, you must run the GOBI Module Carrier Wizard before provisioning can be successfully completed.
TransPort® DR64 Installation Guide 4.3 Command Line Interface (CLI) To stop the DHCP server from serving addresses, use the following command: In order to configure the unit via a serial cable connection, ensure that the unit is connected to a PC (as outlined in Step 6 on page 11 of the Installation section). Also, terminal emulation software (such as HyperTerminal or TeraTerm) will be required. 4.3.1 CLI Notes • To view the current configuration settings, enter the command CONFIG C SHOW.
TransPort® DR64 Installation Guide 5 Troubleshooting 5.1 TransPort® DR64 Installation Guide 6 Specifications Specifications Troubleshooting Resources General Features: There are several resources available to you for support of your Digi product or resolving configuration difficulties at Digi’s Support site, http://www.digi.com/support/. Try these troubleshooting steps to eliminate your problem. After working through these steps and your problem is not solved, try the resources listed below.
TransPort® DR64 Installation Guide 7 Accessories Antennas - Cellular AC Power Supplies North America (NA) 76000824 International (Intl.) 76000824 DC Power Cords Barrel Plug to Bare Wire TransPort® DR64 Installation Guide 76000833 Mounting Brackets DIN Rail 76000835 Wallmount 76000848 (DR6410) 76000849 (DR6420 / 60) Rackmount 76000840 Direct Mount, Quad Band, 2dBi 76002050 Direct Mount, Penta Band, 2dBi 76002052 Direct Mount, Dual Band, 3dBi DC-ANT-DBDP3 Magnet Mount, Penta Band, 2.
TransPort® DR64 Installation Guide TransPort® DR64 Installation Guide Declaration of Conformity EC Declaration Of Conformity We, of Manufacturer's Name: Digi International Manufacturer's Address: 11001 Bren Road East Minnetonka, MN 55343 EC Declaration Of Conformity Part Number DR64-X1X2-YZZ-AA Where X1 can be: 00, 01, C0, C1, C2, C5, C8, E1, U0, U1, U2, U3, U4 Where X3 can be: A1, A2, A6, B1, B2, B6, I1, I2, I6, J1, J2, J6, P1, P2, P6, Q1, Q2, Q6 Where Y can be: D or W Where ZZ can be: E2, E3, E5,
Copyright © 2011 Digi International Inc. All rights reserved. Digi, Digi International, the Digi logo, a Digi International Company, the Digi web site, Digi Remote Manager, Digi TransPort, and Digi TransPort DR are trademarks or registered trademarks of Digi International, Inc. in the United States and other countries worldwide. All other trademarks are the property of their respective owners.