Digi Connect® ES Device Server Hardware setup guide
Digi Connect ES Device Server Hardware setup guide 90001925 Revision A Date Description June 2014 Revised and replaced document 90000715-88_D to comply with IEC 60601-1 documentation requirements. Disclaimers Information in this document is subject to change without notice and does not represent a commitment on the part of Digi International.
Contents About Digi Connect ES Device Server Technical description 5 Digi Connect ES Device Server models Additional information 6 Recycling and disposal 6 Environmental information 6 Symbol definitions 7 Cautions and warnings 8 Connectors, LEDs, and controls 9 5 Setting up Digi Connect ES Device Server hardware Before setting up the hardware 11 EMC specification 11 Setting up Digi Connect ES hardware Digi Connect ES Device Server Hardware setup guide 12 3
Digi Connect ES Device Server Hardware setup guide 4
About Digi Connect ES Device Server Digi Connect ES Device Server is a high performance, high-reliability serial-to-Ethernet concentrator with extended safety characteristics. Technical description Digi Connect ES provides serial-over-Ethernet connectivity to connect sensitive RS-232-enabled devices to the network. Both serial and Ethernet ports are galvanically isolated, and Ethernet ports offer 10/100 Mbps network interface with an optional Ethernet switch.
Technical description This is a Class I Electrical Device. Alternating current 100-240V, 50-60 Hz 0.2A max Fuse 250V F1A Additional information All Digi Connect ES Device Server models include software in the form of firmware described in the Digi Connect Family User Guide. Go to www.digi.com/products/ serialservers/digiconnectes to get the latest version of the guide, as well as a detailed product datasheet for the Digi Connect ES family of products.
Symbol definitions Symbol definitions Symbol Definition Alternating current Atmospheric pressure limitation Batch code Catalog number Caution Conforms to the European Medical Device Directive 93/42/EEC; self certified Consult instructions for use YYYY Date of manufacture ETH Ethernet connection Functional earth terminal Fuse High voltage Humidity limitation Manufacturer Digi Connect ES Device Server Hardware setup guide 7
Cautions and warnings Symbol Definition Package recycling information QTY Quantity REV Revision number Serial number Temperature limitation Warning WEEE Device was put on the market after 13 August 2005. Conforms to the Directive 2003/108/EC on waste electrical and electronic equipment (WEEE) of the European Parliament. Cautions and warnings CAUTION! • Do not rely on the validity of the data from this device server without validating the integrity of the entire information collection system.
Connectors, LEDs, and controls WARNING! This device contains no user-serviceable parts. No modification of this equipment is allowed. WARNING! In case of smoke, disconnect mains power from the device and discontinue use. WARNING! Do not use this device in areas with high magnetic fields. Connectors, LEDs, and controls Callout Symbol 1 250V F1A Description Fuse Off/On 2 On Off Mains power connector/Power input 3 100-240V 50 - 60 Hz, 0.
Connectors, LEDs, and controls Callout Symbol Description 9 l Ethernet switch LED 10 l Serial LED 11 Find me locater LED 12 Power LED 13 Serial ports (4 or 8) Digi Connect ES Device Server Hardware setup guide 10
Setting up Digi Connect ES Device Server hardware Setting up Digi Connect ES Device Server hardware consists of connecting power to the device, connecting the device to the network, connecting Ethernet devices, and connecting serial devices. Before setting up the hardware CAUTION! It is the installer's responsibility to ensure that this device is installed and put into service according to the EMC specifications below.
Setting up Digi Connect ES hardware Setting up Digi Connect ES hardware Note While following the hardware setup procedure, refer to Connectors, LEDs, and controls on page 9. 1 Place the Digi Connect ES Device Server in a suitable location, noting the following warnings: WARNING! Mount the device server on a wall or place it on a tabletop away from high traffic areas. Keep cables out of reach and off the floor.
Setting up Digi Connect ES hardware 4 (Optional) On SW models, connect up to four additional Ethernet devices to the remaining Ethernet ports (7). Make sure to use straight through Ethernet patch cables when connecting devices to the Digi Connect ES Device Server Ethernet ports. 5 Connect serial devices: Connect each serial device to a serial port (13) on the Digi Connect ES Device Server. If the connection between the device and the network is established, the serial port LED (10) illuminates.
© 2014 Digi International. All rights reserved.