Reference Manual

Regulatory information and certifications United States FCC
ConnectCore® 8X System-on-Module Hardware Reference Manual --
Preliminary
107
RF
band
Peak
antenna
gain Technology Frequencies
WLAN [BW 20 MHz] x 11 overlapping channels, # (center freq. MHz): *
[2400 - 2473 MHz]: 1 (2412), 2 (2417), 3 (2422), 4 (2427), 5 (2432),
6 (2437),7 (2442), 8 (2447), 9 (2452), 10 (2457), 11 (2462)
[BW 40 MHz] x 7 overlapping channels, # (center freq. MHz): *
[2400 - 2473 MHz]: 3 (2422), 4 (2427), 5 (2432), 6 (2437),7 (2442),
8 (2447), 9 (2452)
2.4GHz 4.6 dBi [BW 20 MHz] x 24 non-overlapping channels, # (center freq. MHz):
* [5150 - 5250 MHz]: 36 (5180), 40 (5200), 44 (5220), 48 (5240) *
[5250 - 5350 MHz]: 52 (5260), 56 (5280), 60 (5300), 64 (5320) *
[5470 - 5725 MHz]: 100 (5500), 104 (5520), 108 (5540), 112 (5560),
116 (5580), 120 (5600),124 (5620), 128 (5640), 132 (5660), 136
(5680), 140 (5700) * [5725 - 5850 MHz]: 149 (5745), 153 (5765),
157 (5785), 161 (5805), 165 (5825)
[BW 40 MHz] x 11 non-overlapping channels, # (center freq. MHz):
* [5150 - 5250 MHz]: 38 (5190), 46 (5230) * [5250 - 5350 MHz]: 54
(5270), 62 (5310) * [5470 - 5725 MHz]: 102 (5510), 110 (5550), 118
(5590), 126 (5630), 134 (5670) * [5725 - 5850 MHz]: 151 (5755),
159 (5795)
[BW 80 MHz] x 5 non-overlapping channels, # (center freq. MHz): *
[5150 - 5250 MHz]: 42 (5210) * [5250 - 5350 MHz]: 58 (5290) *
[5470 - 5725 MHz]: 106 (5530), 122 (5610) * [5725 - 5850 MHz]:
155 (5775)
Note A table containing transmit power values will be added in a subsequent revision of this manual.
FCC notices
IMPORTANT: The ConnectCore 8X module has been certified by the FCC for use with other products
without any further certification (as per FCC section 2.1091). Modifications not expressly approved by
Digi could void the user's authority to operate the equipment.
IMPORTANT: OEMs must test final product to comply with unintentional radiators (FCC section 15.107
& 15.109) before declaring compliance of their final product to Part 15 of the FCC Rules.
IMPORTANT: The ConnectCore 8X module has been certified for remote and base radio applications. If
the module will be used for portable applications, the device must undergo SAR testing. This
equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures: Re-orient or relocate the
receiving antenna, Increase the separation between the equipment and receiver, Connect equipment
and receiver to outlets on different circuits, or Consult the dealer or an experienced radio/TV
technician for help.