DECLARATION OF CONFORMITY Manufacturer’s Name: Manufacturer’s Address: DigiTech 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product: Product name: Turbo Flange Product option: all (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.
WARRANTY: We at DigiTech are proud of our products and back-up each one with the following warranty: 1.The warranty registration card must be mailed within ten days after purchase date to validate this warranty. 2. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service. 3.
The Turbo Flange is a multi-function flanger pedal that offers seven different types of flanging effects and CIT™ cabinet modeling. The following sections outline how the knobs and pedal functions will work. 1. Speed Knob Controls the speed of the flange sweep. Turn this knob clockwise to increase the speed, and counter-clockwise to decrease the speed. 2. Depth Knob Controls the depth of the effect. Turn this knob clockwise to increase the depth, and counter-clockwise to decrease the depth. 3.
1 2 3 4 5 11 10 9 6 7 8
5.Type Knob Selects 1 of the 7 different flanger effect types available. 1.VOICE 1 - A classic jet airplane flanger voicing. 2.VOICE 2 - A guttural, growling flanger voicing. 3.VOICE 3 - A tube-like flanger voicing, 4. RISE / FALL - Creates a constant rising flanger sound when the Regen knob is set between the minimum and 12 o’clock positions, or a constant falling flanger sound when the Regen knob is set between the 12 o’clock and maximum positions. 5.
6. Input Jack Connect your instrument to this jack. Connecting a guitar cable to this jack supplies battery power even though the Indicator LED may not be lit. To prolong battery life, disconnect all cables from the pedal when not in use. 7. Pedal Release Pins These two pins are spring-loaded hinges that hold the pedal in place. Push these pins in to release the pedal from the pedal chassis exposing the battery compartment. (See battery replacement diagram.) 8.
11. Out 2 Jack Connect this output to a second amplifier or mixer channel for stereo flanging. Stereo is the best way to get the most effective stereo flange experience from the Turbo Flange pedal. Connections The Turbo Flange has a single input and a pair of outputs. Out 1 is used if the Turbo Flange is being connected to only one amplifier or mixer channel with the pan set to center. Out 2 is used for stereo operation.
Battery Replacement 1. Using the tip of a 1/4” guitar cable, push one of the release pins in on either side of the pedal, and remove the pedal from the pedal chassis. 2. Remove the battery from the battery compartment and disconnect the battery cable. 3. Connect a new battery to the battery cable and put it back in the battery compartment. Make sure the battery cable does not interfere with the spring or pedal switch arm. 4. Place one hole of the pedal over its corresponding pin. 5.
Pedal Pedal Switch Arm 9V DC Battery Pedal Release Pin Battery Compartment Spring Pedal Release Pin Pedal Chassis
SPECIFICATIONS: • Controls - Speed, Depth, Regen,Type, On/Off Pedal • Jacks - Input, Out 1 (Mono), Out 2 • Input Impedance - 1 MOhms • Output Impedance - 100 Ohms • Power Supply - 9V Alkaline Dry Battery • Power Consumption - 4.8Watts (w/optional PS200R power supply) • Battery Life - Approximately 4 hours (with continuous usage) • Dimensions - 4 15/16”(L) x 3 1/8”(W) x 2 1/8”(H)• Weight 1.38 lbs.