Full Product Manual

Device Overview
Warranty
Limitation of Liability
Product of Singapore
2-AXIS SMART CUBE
DIGITAL LEVEL
QUICK START GUIDE
DWL-90 (0.05° resolution)
Digi-Pas
®
DIGIPAS
Battery Compartment
In no event shall DIGIPAS TECHNOLOGIES INC., (hereinafter,
“the Company”) be liable to you or any third party for any indirect,
special, incidental, exemplary or consequential damages of any
kind resulting from any breach of warranty or from the performance
or use of the product. This includes without limitation: property
damage, loss of value of the product or any third party products
that are used with the product, or loss of use of the product or any
third party products that are used with the product, even if the
Company has been advised of the possibility of such loss or
damages. The Company’s total cumulative liability arising from or
related to the product, whether in contract, tort (including
negligence) or otherwise, shall not exceed the amount actually
paid by you for the product. Some states and/or jurisdictions do
not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to
you. If any limitation of liability shall be deemed invalid by any
applicable law, then the limitations of liability set forth above shall
apply to the maximum extent permitted under applicable law.
- This device contains MAGNET!
- New device needs to be calibrated on the first time use.
2
1
5
6
7
8
10
11
9
1. LED display
2. MODE button: -°(Degree), mm/M & In/Ft
3. Magnet
5. Power button: - Press & Hold to turn device on/off
- Start calibration in calibration mode
7. Level directional arrow indicator
8. Alt. Zero Indicator
9. Level measurement value
10. Unit indicator
11. Bluetooth indicator
- Press & Hold to freeze measurement
value on the display
4. Aluminium Base
6. Alt. Zero button: - Set any angle to 0° as reference
- Press & hold to turn bluetooth on/off
- Press & hold while power on device
to enter Calibration Mode
3
4
Technical Specification
Dimension : 2.4" x 1.48" x 2.28"
Weight : 90 Grams
Operating Temp : 0° ~ +50°(Celsius)
Storage Temp : -10° ~ +60°(Celsius)
Battery : 2 x AAA 1.5V
Calibration Instruction
Press ‘Alt. Zero’ button while turn on the device
on. The screen will display flashing “CAL1”
Place the device on a flat and clean surface
(Figure 1), press power button once, the screen
will display countdown, wait until screen
countdown reach “1” and show “CAL2”.
Rotate the device (180°) parallel to the surface
(Figure 2) then press power button again, the
screen will display countdown, wait until screen
countdown reach “1” and show “CAL3”.
Position the device vertically (-90°) on a vertical
surface (Figure 3), press power button again,
the screen will display countdown, wait until
screen countdown reach “1” and show “CAL4”.
Rotate the device 180° parallel vertically to the
surface (+90°) shown on Figure 4 then press
power button again, the screen will display
countdown, wait until screen countdown reach “1”.
Calibration is done.
1.
2.
3.
4.
5.
6.
Note: Ensure the device is kept still during calibration
Caution
Digi-Pas® device is calibrated in the factory for maximum accuracy. User
can re-calibrate when necessary.
Refer to www.digipas.com for video demonstration on how to calibrate the
device.
Cleaning
Calibration illustration
Figure 1
Figure 2
Figure 3 Figure 4
180°
180°
•
•
•
Keep the level dry and clean. Remove any
moisture or dirt with a soft dry cloth.
Do not use harsh chemicals, strong detergents or
cleaning solvents to clean the level.
Do not submerge device in water while cleaning.
Wiping or cleaning on device surface is sufficient.
Note: 2-Axis reading only available through “Digipas Smart Level” app. App is available in Android
& iOS
Digi-Pas® Digital level is warranted to the original purchaser to be
free from defects in workmanship and material. Digipas will, at its
option, repair or replace any detective part which may malfunction
under normal and proper use within a warranty period of 1 (one)
year from the date of shipment. This one year warranty clause is
NOT applicable to European Union (EU) member states.
Purchases made in EU member states will be covered by the
existing consumer laws across the European Union, which provide
statutory warranty rights in addition to the coverage of one year
warranty period. The foregoing warranty shall not apply to defects
resulting from misuse, abuse or transfer by the Buyer,
Buyer-supplied software or interfacing, unauthorized modification
or operation outside of environmental specifications for the
product. Digipas does not warrant that the operation of the
instrument software, or firmware, will be uninterrupted or error free.
The exclusive remedy under any and all warrants and guarantees,
expressed herein, and we shall not be liable for damages from loss
or delay of equipment uses, consequential, or incidental damage.
No other warranty is expressed or implied. Digipas specifically
disclaims the implied warranties of merchantability and fitness for a
particular purpose.
This user manual is printed in small font size for paper saving
purpose to protect the environment. Softcopy is available at
http://www.digipas.com/catalog-manual.
User Self-Calibration video is available in YouTube.
video is available in YouTube.
Loosen screw by turning anti-clockwise direction
using Philips screwdriver
Pull out battery cap
Insert two (2) piece AAA batteries follow polarity
direction as indicated above & screw back the
battery compartment
Caution:
Please ensure batteries are inserted in correct
polarity direction for device to work.
Manufactured by
Digipas Technologies Inc.
Email: [e-mail]
www.digipas.com
JQC-2-00091-99-001