User manual
Remote Control
R&S
®
RTO
501User Manual 1316.0827.02 ─ 06
Setting parameters:
<DiagramName> String with the diagram name
<Source> NONE | C1W1 | C1W2 | C1W3 | C2W1 | C2W2 | C2W3 | C3W1 |
C3W2 | C3W3 | C4W1 | C4W2 | C4W3 | M1 | M2 | M3 | M4 | R1 |
R2 | R3 | R4 | XY1 | XY2 | XY3 | XY4 | MRESult1 | MRESult2 |
MRESult3 | MRESult4 | MRESult5 | MRESult6 | MRESult7 |
MRESult8 | SBUS1 | SBUS2 | SBUS3 | SBUS4 | D0 | D1 | D2 |
D3 | D4 | D5 | D6 | D7 | D8 | D9 | D10 | D11 | D12 | D13 | D14 |
D15 | MSOB1 | MSOB2 | MSOB3 | MSOB4
Waveform to be assigned, see chapter 16.2.2.2, "Waveform
Parameter", on page 419
Usage: Setting only
LAYout:SIGNal:AXIS <DiagramName>, <Source>, <XSource>
Creates an XY-diagram by adding a second waveform to a diagram with a channel, math
or reference waveform.
Setting parameters:
<DiagramName> String with the name of the diagram where the waveform is added.
<Source> C1W1 | C1W2 | C1W3 | C2W1 | C2W2 | C2W3 | C3W1 | C3W2 |
C3W3 | C4W1 | C4W2 | C4W3 | M1 | M2 | M3 | M4 | R1 | R2 | R3 |
R4
Waveform to be added, see chapter 16.2.2.2, "Waveform Param-
eter", on page 419
<XSource> ON | OFF
If on, the added waveform is assigned to the x-axis.
If off, it is assigned to the y-axis.
Usage: Setting only
LAYout:SIGNal:UNASsign <Source>
Removes the specified waveform from the diagram.
Setting parameters:
<Source> NONE | C1W1 | C1W2 | C1W3 | C2W1 | C2W2 | C2W3 | C3W1 |
C3W2 | C3W3 | C4W1 | C4W2 | C4W3 | M1 | M2 | M3 | M4 | R1 |
R2 | R3 | R4 | XY1 | XY2 | XY3 | XY4 | MRESult1 | MRESult2 |
MRESult3 | MRESult4 | MRESult5 | MRESult6 | MRESult7 |
MRESult8 | SBUS1 | SBUS2 | SBUS3 | SBUS4 | D0 | D1 | D2 |
D3 | D4 | D5 | D6 | D7 | D8 | D9 | D10 | D11 | D12 | D13 | D14 |
D15 | MSOB1 | MSOB2 | MSOB3 | MSOB4
See chapter 16.2.2.2, "Waveform Parameter", on page 419
*RST: NONE
Usage: Setting only
Command Reference