DICE Auxiliary interface for iPod Installation Guide/User Manual
Copyrights and Trademarks Copyright 2008 DICE Electronics, LLC. The DICE Electronics logo is a trademark of DICE Electronics, LLC. iPod is a trademark of Apple, Inc. All rights reserved. Printed in the U.S.
Table of contents Copyrights and trademarks Table of contents Warning and safety Product registration Supported iPod models Charging 3 4 5 6 7 8 Integration kit contents Gain adjustment Installation Using the AUX integration Troubleshooting Installation notes Disclaimer and Warranty 9 10 11 14 15 16 18 4
Warning and safety! Please read these instructions carefully before proceeding. Failure to follow instructions may result in improper operation or injury. Neither DICE Electronics, LLC. nor Apple Inc., its regional offices, distributors or resellers take any responsibility for any damage or injury as a result of using the integration kit. - Do not open, disassemble or alter the interface in any way. - Do not insert anything into the casing.
Congratulations on your purchase Thank you for purchasing the DICE integration kit for iPod. Please review our user manual and installation guide before operating the unit. This interface was designed and manufactured to seamlessly integrate with your vehicle's factory entertainment system. Product registration In order to validate your warranty period and to receive telephone or online support, you MUST register your DICE product. To register your DICE product, please complete the following steps: 1.
Supported iPod models and firmware version requirements FW:3.1.1 FW:1.2.1 FW:1.0.3 iPod iPod iPod classic 4th generation 20GB 40GB 4th generation color display 20GB 30GB 40GB 60GB 80GB 160GB FW:1.2.1 FW:1.4.1 iPod iPod mini 5th generation (video) 30GB 60GB 80GB 4GB 6GB FW:1.3.1 FW:1.1.3 FW:1.0.3 iPod nano 3th generation (video) 4GB 8GB FW:1.1.
Charging The interface automatically charges the battery of the iPod when connected and the key is in the ACC/ON position. Most vehicles turn off ACC power when the key is in the OFF position and the iPod will stop playing and charging. However, in some vehicles the ACC power is always on and the iPod should be disconnected to prevent draining the vehicles battery. Charging icon will appear on the upper right corner of the iPod screen to indicate charging.
Integration kit contents 1 interface unit 1 auxiliary audio/power cable 1 iPod dock cable 1 User manual iPod dock cable interface unit REM DICE interface for iPod for AUX GND +12V Installation Guide/User Manual user manual auxiliary audio/power cable 9
Gain adjustment The potentiometers located on the interface unit are used to adjust the gain settings for the iPod and AUX jack to properly match the radio's input level. We recommend setting the AUX module's output level to match the factory CD or AM/FM station's sound level. Increase/decrease Interface unit iPod gain setting 10 mini jack gain setting NOTE: Use a small phillips head screw driver or a plastic pot adjuster tool to adjust the potentiometers.
Installation instructions Installation should only be performed by a qualified professional. Beware of sharp edges to avoid injury and exercise caution when removing trims as they may break. The interface unit should be placed at an accessible location, such as in the glove box, the center console or under the front seat. 1 Pull vehicle into service bay. 2 Make sure that the radio code is available before disconnecting battery. Disconnect both battery terminals.
4. You can access the factory AUX port located on the back of the radio. Connect the red and white colored AUX audio connectors into the red and white colored receptacle on the radio. If the factory AUX port already has something connected, it must be disconnected. Connect the +12 volt, ground and remote wire leads to their proper sources.
5 Connect the AUX audio cable and the iPod docking cable to the interface unit. If an additional audio device will also be used (mp3, DVD player, etc.) connect its audio cable to the 1/8” mini-jack. Apply cable ties to secure the cables. receptacle 1/8” mini-jack iPod dock input power adapter input iPod docking cable receptacle power/antenna cable 6 Verify that all connections have been properly made. 7 Reconnect the car's battery.
Using the AUX integration Connect the iPod to the dock cable and select the auxiliary source on the radio. The charging indicator should appear on the iPod and a selected song will start to play. If an additional audio device is connected through the 1/8” mini-jack, it will become active when the iPod is disconnected. AUX source selector Song Title Artist Name Album Name CD AUX DISC VOL disc COMPACT PUSHPWR CLOCK DIGITAL AUDIO AUX IN SEEK SKIP SCAN RPT TUNE 1 of 12 2:42 A.
Troubleshooting Problem Cannot select the interface using the radio. Solution Check all connections. With the ignition OFF disconnect vehicle harness from module for a few seconds and reconnect. Turn ignition to ACC/ON. Verify that the correct button is used to access the AUX input. No audio from iPod source Reset the iPod. Verify proper connection to iPod/interface. iPod does not charge Check all connections. Reset iPod and make sure iPod charges while connected to computer or wall charger.
Installation notes: Installed by: Install date: Other notes: 16 Illustration:
Notes: 17
Disclaimer and warranty Important disclaimer, please read! Unauthorized reproduction or reverse engineering is strictly prohibited! Intellectual property included is distributed under specific license agreement with respective owners and is licensed only, not sold. No warranty, explicit or implied, is stated. Neither DICE Electronics, LLC., nor any of its agents, distributors, dealers or vendors shall be liable for damages.
AUX-iPod www.diceelectronics.
