ENGLISH Wide LCD-TV Instruction Manual LT-40H6LVH ● LT-40T6LVH ● LT-46T6LVH ● Please read this manual carefully before operating your set.
Warnings Warnings WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : The unit is operated at dangerous voltages. The unit may only be opened by an authorised specialist. All maintenance and servicing work must be carried out by an authorised company. Repairs that are carried out incorrectly could result in fatal injuries to the user.
ENGLISH Warnings Warnings Cleaning Unplug the TV before cleaning the face of the LCD Screen. Dust the TV by wiping the screen and cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth. Do not use liquid or aerosol cleaners. POWER The main plug should be inserted fully into the power outlet to avoid a fire hazard. Hold the plug firmly when unplugging. If you pull the cord, the cord may be damaged. Prevent dust collecting on the power plug pins or outlet.
Warnings Warnings Safety This LCD TV have been engineered and manufactured to assure your safety. You can prevent serious electrical shock and other hazards by keeping in mind the following. Do not place anything heavy, wet or magnetic on the LCD TV or the power cord. Never cover the ventilation openings with any material and never touch them with metallic or inflammable materials. Avoid operating the LCD TV in extreme heat, humidity or areas affected by dust.
ENGLISH Contents Contents uBefore operating the set, please read this manual carefully.
Contents Contents uBefore operating the set, please read this manual carefully.
ENGLISH Supplied Supplied Accessories Accessories uMake sure the following accessories are provided with Product. Batteries (2EA) Remote controller ● ● ● LT-40H6LVH LT-40T6LVH LT-46T6LVH NORSK DANSK SUOMI Wide LCD-TV Instruction Manual SVENSKA ENGLISH AC cord Please read this manual carefully before operating your set. VGA cable Instruction manual PC AUDIO IN cable Battery installation uInserting batteries 1 Remove the battery cover by pulling it upward in the direction shown by the arrow.
Installation Installation Installation Options uYou can install the TV on a wall or place it on a table-like surface. uTo eliminate any risk of injury from the TV falling, it should be mounted securely. Wall Installation Do not install the TV on a weak wall surface, like plaster etc. Caution When the TV is placed into a cupboard, the distance between the TV and the wall have to leave minimum 60mm square as below.
ENGLISH Connecting Connecting Speaker Speaker L Connecting TV and Speaker(LT-40T6LVH, LT-46T6LVH) 1 Fix the bracket onto the guide pole located on the rear of TV and Speaker. speaker joint bracket 2 Clamp the speaker and the TV together fasten the screws. 3 Connecting the speaker audio cable to the external speaker output jack on the TV. External speaker output jack 4 Fix the speaker audio cable on the quick clamp✽ located on the rear of TV.
Controls Controls Front Panel [LT-40H6LVH] [LT-40T6LVH, LT-46T6LVH] 1. ON/OFF Switches TV set on or off. 2. MENU Displays a menu. 3. ▼PR ▲ (Programme Up/Down) Selects a programme or a menu item. 4. ◀VOL ▶ (Volume Up/Down) Adjusts the volume./ Adjusts menu settings. 5. TV/AV Selects TV, SCART1, SCART2, S-VIDEO, COMPONENT, PC ANALOG, HDMI./ Clears the menu from the screen. 6. Power Indicator Illuminates in red when the TV is in standby mode./ Illuminates in green when the TV is switched on. 7.
ENGLISH Controls Controls Rear Panel 1. PC ANALOG IN (D-SUB) 2. HDMI (High Definition Multimedia Interface) IN Connect to the HDMI jack for device with HDMI output. 3. PC AUDIO IN Connect the audio cable from the PC to the PC AUDIO IN of the set. 4. H/P (Headphone out) Connect a headphone to this socket. 5. Coaxial OUT Connect the coaxial audio cable from the digital audio device to the Coaxial OUT of the set. 6.
Controls Controls All the functions can be controlled with the remote controller. Some functions can also be adjusted with the buttons on the side panel of the set. Remote controller Before you use the remote controller, please install the batteries. 1. POWER Turns the TV on from standby or off to standby mode. 2. MUTE Turns the sound on and off. 3. NUMBER buttons Selects programme numbers. 4. PICTURE( ) Recalls your preferred picture setting 5. SOUND( ) Recalls your preferred sound setting 6.
ENGLISH Controls Controls 13. VOLÏ/VOLq(Volume Up/Down) Adjuste the sound level. 14. ARC( ) Selects a screen mode- 16:9, 14:9, 4:3, 16:9 Zoom, 14:9 Zoom, 4:3 Zoom and Auto. 15. TELETEXT Buttons These buttons are used for TELETEXT. For further details, see the ‘TELETEXT’ section. 16. LIST Displays the programm list menu. 17. PIP( ) Displays a PIP(Picture In Picture) screen. 18. INPUT( ) Selects the AV source of sub picture in PIP mode. 19.
Basic Basic Operation Operation Turning the TV On and Off Standby Setup: The AC power cord must be set up and connected to have the TV in standby mode ready to be turned on. Press the ON/OFF button on the front panel of the TV to go into standby mode. 1 If the TV is in standby mode, press the POWER button on the remote controller or the TV itself to turn the TV on. 2 Press the POWER button again on the remote controller or the TV itself to turn the TV off.
ENGLISH Basic Basic Operation Operation On screen menu language selection The menu can be displayed on the screen in desired language. First select your language. 1 Press the MENU button. 2 x/PRy y button. Select the Setup menu with PRx 3 Press the Ïq button to select the Setup menu. 4 x/PRy y button. Select the Language with PRx 5 Press the Ïq button to select the Language. 6 x/PRy y button to select your desired language. Press the PRx 7 Press the TV/AV button.
On Screen Menus and Display 1 Press the MENU button to display main menu. 2 x/PRy y button to select menus-Picture, Press the PRx Sound, Special, Setup. 3 Adjust each menu with the Ïq button. 4 Press the MENU button to return to preceding menu. 5 Press the TV/AV button to finish adjusting menu.
ENGLISH Setting Setting up up TV TV Programme Programme Once you have preset the programme, you will be able to use the x/PRy y or NUMBER buttons to scan the programme you PRx programmed. Programme can be tuned using Auto or Manual programme menu. Auto Programme All programme that can be received are stored by this method. It is recommended that you use Auto programme during installation of this set. 1 Press the MENU button. 2 Select the Setup menu. 3 Press the Ïq button to select the Setup menu.
Setting Setting up up TV TV Programme Programme Manual Programme Manual Programme lets you manually tune and arrange the programme in whatever order you desire. Also you can assign a programme name with 8 characters to each programme number. 1 Press the MENU button. 2 Select the Setup menu. 3 Select Manual Programme menu. 4 Select the Programme with the Ïq button or NUMBER buttons. 5 x/PRy y button to select the System. Press the PRx 6 Select a TV system with the Ïq button.
ENGLISH Setting Setting up up TV TV Programme Programme Programme Edit This function enables you to delete, favourite, move or skip the stored programme. Also you can move some programme to other programme numbers or insert a blank programme data into the selected programme number. 1 Press the MENU button. 2 Select the Setup menu. 3 x/PRy y button to select Programme Edit. Press the PRx 4 Press the Ïq button to start the Programme Edit. x/PRy y and Ïq.
Picture Picture Control Control You can adjust Colour Temperature, Contrast, Brightness, Colour, Sharpness and Tint(Only in NTSC mode) to the levels you prefer. Manual Picture Control 1 Press the MENU button. 2 x/PRy y button, and Select Picture using the PRx press the Ïq button. 3 Select Colour Temperature using the Ïq button. 4 x/PRy y button to select a particular colour tone. Press the PRx If you select User, you can control the value manually. Note a.
ENGLISH Picture Picture Control Control PICTURE Effect 1 Press the PICTURE( ) button. 2 Press the PICTURE( ) button repeatedly to select Picture effect. Each press of the button changes the screen display as below.
Sound Sound Control Control You can select your preferred sound setting; Flat, Music, Movie or Speech and you can also adjust the sound frequency of equalizer, balance. If you switch AVL to on, the set automatically keeps on an equal volume level even if you change programme. Manual Sound Control 1 Press the MENU button. 2 x/PRy y button, and press Select the Sound using the PRx the Ïq button.
ENGLISH Sound Sound Control Control SOUND Effect 1 Press the SOUND( ) button. 2 Press the SOUND( ) button repeatedly to select. Each press of the button changes the screen display as below. Flat Music Movie Speech User SRS WOW Auto Sound Control * The sound Flat, Music, Movie and Speech are programmed for good sound reproduction at the factory and cannot be changed.
Other Other functions functions Clock Setting the clock is necessary in order to use the various timer features of the TV. You can set automatic TV On or Off time. 1 Press the MENU button. x/PRy y button to select the Setup menu. 2 Press the PRx Then press the Ïq button. x/PRy y button to select Clock menu. 3 Press the PRx Then press the Ïq button. Setup Clock x/PRy y or number buttons Set the present time with the PRx on remote controller.
ENGLISH Other Other functions functions N.R.(Noise Reduction) The N.R feature improves the picture quality by setting to Mode1 or Mode2. If you experience noise on a certain programme, set the N.R to Mode1 or Mode2 for this programme, to obtain the optimum picture. 1 Press the MENU button, select the Special. 2 Press the Ïq button to select N.R.. 3 Press the Ïq button to select Off, Mode1 or Mode2. 4 Press the TV/AV button to return to normal TV viewing.
Other Other functions functions Childlock Childlock menu is necessary in order to disable the buttons on the front/side panel of the set. Especially it is useful to prevent unauthorized viewing. x/PR button to select Childlock. 1 Press the PRx 2 Press the Ïq button repeatedly to select On or Off. * When the setting is Childlock On, the buttons except ON/OFF button on the front/side panel of the set is disabled. * When the setting is Childlock Off, the buttons on the front/side panel of the set is enabled.
ENGLISH Other Other functions functions I/II Mono sound selection In stereo reception if the stereo signal is weak, you can switch to mono by pressing the I/II button twice. In mono reception the depth of sound is improved. To switch back to stereo, press the I/II button twice again. Language selection for dual language broadcast If a programme is received in two languages (dual language), you can switch to DUAL I, DUAL II, DUAL I+II by pressing the I/II button repeatedly.
Other Other functions functions Sleep timer You don’t have to remember to switch the set off before you go to sleep. The sleep timer automatically switches the set to standby after the preset time elapses. Press the SLEEP button to select the number of minutes. The display will appear on the screen, followed by 0, 15, 30, 60, 120. The timer begins to count down from the number of minutes selected. Note a. To view the remaining sleep time, press the SLEEP button once. b.
ENGLISH Other Other functions functions Calling the programme list You can check the programmes stored in the memory by displaying the programme list. Displaying programme list 1 Press the LIST button to display the Programme list menu. The programme list appears on the screen. One programme list page contains twenty programmes as right picture. Note a. You may find some blue programmes. They have been set up to be skipped by auto programming or in the programme edit mode. b.
TELETEXT TELETEXT TEXT On/Off Press the TEXT button to switch to TELETEXT. The initial page or last selected page appears on the screen. The first page number indicates your selection, while the second shows the current page displayed. 1 Press TEXT button once, displays the TELETEXT pages. 2 Press MIX button once more, displays the TELETEXT pages superimposed on the TV picture. 3 Press the TEXT button to switch off TELETEXT once more, Text mode is off, and TV mode appears.
ENGLISH TELETEXT TELETEXT Special TELETEXT functions MENU Functions TEXT Changes TELETEXT mode SIZE Selects double height text. Press this button to enlarge the top half of the page. Press this button again to enlarge the bottom half of the page. Press this button again to return to the normal display. HOLD Stops the automatic page change, which will occur if a TELETEXT page consists of 2 or more sub pages.
External Equipment Connection You can connect additional equipment, such as VCRs, camcorders etc. to your set. Examples are shown below. Antenna connection Connect RF out on the VCR to the Antenna input on the rear of the TV. SCART 2(AV 2) IN 1 2 3 Connect the AV out jacks on the AV device to the SCART 2 on the TV. Use the TV/AV button to select SCART2 mode. Press the PLAY button on the DVD. In Scart 2 jack, selectable A/V out is available.
ENGLISH External Equipment Connection Connecting to HDMI (High Definition Multimedia Interface) 1 Connect an HDMI cable between the “HDMI IN” jack on the TV and the HDMI OUT jack on the set-top box. Please check that the HDMI source is powered on. 2 Press the TV/AV button to select HDMI mode. S-VIDEO IN If the optional equipment you are connecting has an S-VIDEO jack, you can use an S-VIDEO cable for improved picture quality(compared to an A/V cable).
Connecting the PC as a monitor This function is possible only when the set is in PC mode. Use the TV/AV or TV/PC button on remote controller. Picture adjustment You can adjust picture Colour Temperature, Contrast, Brightness, Colour, Sharpness and ARC as you prefer. 1 Press the TV/AV button to select the COMPONENT, PCANALOG or HDMI mode. 2 Press the MENU button. 3 Select the Picture. 4 Select Colour Temperature using the Ïq button. 5 x/PRy y button to select a particular colour tone.
ENGLISH Connecting the PC as a monitor Sound adjustment 1 Press the MENU button. 2 Select the Sound menu. 3 x/PRy y button to select the desired sound item; Press the PRx Equalizer, Balance, AVL, SRS WOW, Headphone or Input. 4 Press the Ïq button to make desired adjustment. 5 Press the Ïq button in Equalizer to set the Equalizer. 6 x/PRy y button to select your Press the PRx preferred setting ; Flat, Music, Movie, Speech or User. To set the Equalizer User. x/PRy ybutton. a.
Connecting the PC as a monitor Setup This function is to adjust picture to left/right and up/down as you prefer. 1 Press the MENU button. 2 Select the Setup menu. 3 x/PRy y button to select the desired item. Press the PRx 4 Press the Ïq button to make desired adjustment. 5 Press the TV/AV button to exit menu H-Position (Horizontal Position) This function is to adjust picture to left/right as you prefer. V-Position(Vertical Position) This function is to adjust picture to up/down as you prefer.
ENGLISH Connecting the PC as a monitor PC INPUT 1 Connect the PC IN cable (D sub cable) from the monitor output socket of the PC to the PC ANALOG IN socket of the set. 2 Connect the PC AUDIO IN cable from the PC to the PC AUDIO IN of the set. 3 Press the TV/AV or TV/PC button to select PC-ANALOG mode. 4 Switch on the PC, and the PC screen appears on the set. The set can be operated as the PC monitor.
Product Specifications Model LT-40T6LVH/LT-40H6LVH Television system LT-46T6LVH PAL-BG, I, DK/ SECAM-BG, DK, L Television programme VHF: 2~13 UHF: 21~69 Cable: S1~S41 LCD Panel 40" Wide TFT LCD Panel Resolution WXGA(1366 x 768) Power consumption 46" Wide TFT LCD 220W 270W External antenna impedance 75Ω Audio output 10W +10W External IN/OUT ports • HDMI IN • S-VIDEO IN • HEADPHONE JACK • PC-ANALOG IN • PC AUDIO IN • SCART 1 IN • SCART 2 IN • COAXIAL OUT • ANTENNA IN • COMPONENT IN
ENGLISH Troubleshooting Troubleshooting Problem Check item No picture on screen and no sound from speakers. • Make sure the remote control is not in the standby mode (The POWER/Standby indicator is red.) • Turn on the MAIN POWER button on the top of the display. No picture/No picture from AV terminal. • Check the brightness setting of the display. • Lamp may have malfunction. • Make sure a cable with no VIDEO input signal is connected to the S-VIDEO INPUT terminal.
