DIAMOND VIEW MONITORS A TRADE MARK OF MITSUBISHI ELECTRIC AUSTRALIA PTY. LTD. DV19NF Colour Monitor 19” (48.3cm) CRT Size, 18” (45.7cm) Max.
Table of Contents Safety Instructions for Display Monitors....................................................................................... ii Maintenance................................................................................................................................................ iii Chapter 1 Introduction.......................................................................................................................................1 Unpacking the Package ......................
Copyright Copyright © 2000 Mitsubishi Electric Australia Pty. Ltd. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. Disclaimer Mitsubishi Electric Australia Pty. Ltd.
Safety Instructions for Display Monitors 1. The AC plug isolates this equipment from the AC power supply. 2. Unplug the monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3. Slots and openings in the cabinet and the back or bottom are provided for ventilation. They must not be blocked or covered.
Maintenance ✘ Do not expose the monitor to direct sunlight or heat. ✘ Do not spill liquid onto the monitor. ✘ Do not attempt to open the monitor. You may be hurt by electric shock. For service, call your place of purchase. Opening your monitor may also void warranty. ✘ Do not use your monitor when magnets or electronic products are operating nearby. ✘ Do not use harsh chemicals or strong cleaning solvents to clean the monitor screen. Wipe it with clean, soft clothes applied with mild solution.
Introduction Unpacking the Package 1 Check following items. If they are missing or damaged, consult your place of purchase immediately. 9 Colour monitor 9 Swivel base 9 User’s manual 9 D-Sub signal cable 9 Power cord 9 Mac adapter Locate the model name and the serial number labeled on the back of your monitor. Write down the related information of your monitor and dealer in the space on page ii for future reference.
9 Easy to Use On Screen Display The On-Screen Display (OSD) allows you to adjust all settings simply with onscreen menus. 9 Power Saving Function The power management complies with VESA DPMS standard. When the system is idle (off mode), the monitor automatically cuts its power consumption up to 95%. 9 Green Commitment No CFCs are used in the manufacturing process of your monitor. It complies with the US government’s Energy Star standards and the rigorous standards of the Scandinavian countries.
Getting Started 2 Installing the Monitor This monitor is equipped with an autosensing power supply for voltage ranges 100~240V AC, 50~60Hz. To install the monitor : 1. Make sure that the system power is turned off. 2. Please refer to the instructions below to connect the signal cable through D-SUB or BNC. 3. Connect the power cord to the monitor and attach it to power source. 4. Turn on the computer and the monitor. Connecting the Signal Cable Your DV19NF provides D-SUB and BNC signal connectors.
Connecting through D-SUB signal connector 1. Make sure that the system power is turned off. 2. Connect the computer end of the DSUB cable to the 15-pin output connector on the video board of your computer. 3. Connect the monitor end of the DSUB cable to the D-SUB receptacle on the back of the monitor. Connecting through BNC signal connector 1. 2. 3. Make sure that the system power is turned off. Connect the computer end of the BNC cable to the output connector on the video board of your computer.
Adjusting the Monitor A Look at the Control Panel 3 Adjusting the Monitor You can adjust the monitor with the On-Screen Display (OSD) menus. There are 6 keys for user’s control. They include Exit, , , Enter. Auto and Power Switch. The following is the introduction: Panel key introduction 1. Auto: Intelligent key used for auto-calibration of picture size and position. 2. Exit key : returns to last page, saves or quits the menu system. 3.
Selecting function and making adjustments 1) Auto (Auto-calibration hot-key) Pressing Auto, the monitor will automatically adjust the display’s size and position to the optimum settings. In some cases , or for some applications , these settings may need to be fine tuned using the Geometry controls. 2) Contrast hot-key mode 1. Press to enter contrast hot-key mode 2. Press or to adjust the setting. 3) Brightness hot-key mode 1. Press to enter brightness hot-key mode. 2.
Make adjustments 1. In Main Menu: Press or to locate the item you desire to change. 2. Press Enter to go into the Sub Menu.
3. Press or to locate the function item. Then press Enter and or to make the adjustment. 4. 5. Press Exit to save the setting. Press Exit to return to main menu. Control functions available in main menu 1. Luminance Contrast: adjusts the difference between the light and dark areas. Brightness: adjusts the brightness of the display. 2. Geometry Hor. Position: adjusts the horizontal position of the display. Hor. Size: adjusts the display width. Ver.
Unbalance: adjusts the pincushion balance if both sides of the display are bowed toward the left or right. Trapezoid: makes the vertical edges of the display parallel. Parallelogram: aligns the top and bottom edges of the image. Top corner: adjusts the edge curvature at the top corners of the image. Bottom corner: adjusts the edge curvature at the bottom corners of the image. 3.
4. Recall geometry preset setting Locate and press Enter to recall the preset settings. The word “Recall” will keep blinking on the screen in the process of recall. This page is also a “status display” that shows current horizontal and vertical frequencies. Please note that the resolution data is only displayed if you are using a graphics signal that corresponds with one of the monitor’s presets. 5.
Note: ) The setting of each parameter is represented by a numeric value and corresponding scale. ) The on-screen menu will automatically disappear after 20-seconds of inactivity. If changes have been made, the monitor will automatically save them. Timing Setting By making adjustments of your video card settings, you can set the timing and the refresh rate to your preferences. The monitor will automatically save the settings.
Factory Preset Timings Mode Resolution Industry Industry VESA VESA VESA MAC VESA VESA VESA VESA 640 x 400 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1280 x 1024 1280 x 1024 1600 x 1200 Vertical Horizontal Frequency (Hz) Frequency (KHz) 70 60 75 85 75 75 85 75 85 75 12 31.47 31.47 46.88 53.67 60.02 60.24 68.68 79.98 91.15 93.
Troubleshooting and Useful Hints 4 Troubleshooting Make sure that your monitor is properly installed if you encounter any trouble using this product (For hardware installation, see Chapter 2, Getting Started). If the problems persist, check this chapter for possible solutions. 9 There is no picture on the screen. Check: Video sync signal. The video sync signal from the graphics card must be as specified for the monitor. Power saving mode. Press any key and move the mouse to deactivate the mode.
9 Colours are impure. Check the signal cable and connector pins. If there are bent or missing pins, consult your place of purchase. Adjust related settings. See Chapter 3, Adjusting the Monitor. Move any sources of magnetic fields away from the monitor. These include speakers and power supplies. 9 There are two horizontal damper lines visible on the screen. These lines are damper lines required by the aperture grille technology, They usually blend into background and are not noticeable.
Need More Help? If your problems remain after checking this manual, please contact your place of purchase or contact: Australia Visit the Mitsubishi Electric Australia web site at www.mitsubishi-electric.com.
Specifications 5 Picture Tube Size 19” (48.3cm) diagonal Type Natural Flat Tube AG pitch 0.25mm aperture grille pitch (at center) 0.27mm aperture grille pitch (at edges) Surface coating AR film (AR, AS) coating Maximum Viewable Size 18” (45.7cm) diagonal Power Supply (Universal) Input voltage 100~240 V AC, 50~60 Hz (Universal) Power consumption(Max.) 150W Max.
Ambient Temperature Operating +5°C ~ +40°C / +41°F ~ +104°F Storage -20°C ~ +60°C / -4°F ~ +140°F Humidity Operating 20% ~ 90% Storage 10% ~ 90% Dimensions (W x H x D) 474 mm (W) x 485 mm (H) x 483 mm (D) Weight (net) 28 Kg 17
