Installation guide

ManualsBrandsDialogic ManualsComputer equipmentBrooktrout TruFax

Before using your BRI service, you must configure

certain parameters. See your LAN Fax documentation

for details.

See Figure 4 for pinout details for your board:

Figure 4. Connector Pinouts

Understanding LED Signals

LEDs on the Mounting Bracket

The LEDs on the mounting bracket provide

information about the status of the different systems

on the board. To identify and locate these LEDs, see

Figure 5.

The following tables describe how the end panel

LEDs provide information:

BRI Status LED

Channel LEDs

Board Status LED

Figure 5. Dialogic® Brooktrout® TruFax® BRI PCI

ExpressSeries Board

LEDs on the Dialogic® Brooktrout®

Board

The LEDs on the board provide information about the

status of the board. To locate these LEDs, see

Figure 5.

The following table describes how the LEDs on the

board provide information:

Using the Dialogic®

Brooktrout® Board

Once you have installed the TruFax® BRI board, install and

configure your fax software application according to

instructions included with the software. After you have set

up your software to support the board, your board provides

support for your specific application

Getting Help

Dialogic provides technical support for customers who have purchased

hardware or software products from Dialogic. If you purchased products

from a reseller, please contact that reseller for technical support. This

equipment contains no user serviceable parts and is not intended for repair by

unauthorized personnel.

If you experience problems with the board, please use the web site below for

repair or warranty information. If the equipment is causing harm to the

telephone network, the telephone company might request that you disconnect

the equipment until the problem is resolved:

www.dialogic.com/support/

reproduce this document in whole or in part without permission in writing from Dialogic

Corporation at the address provided below.

All contents of this document are subject to change without notice and do not represent a

commitment on the part of Dialogic Corporation or its subsidiaries. Reasonable effort is

made to ensure the accuracy of the information contained in the document. However, due

to ongoing product improvements and revisions, Dialogic Corporation and its subsidiaries

do not warrant the accuracy of this information and cannot accept responsibility for errors

or omissions that may be contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH

DIALOGIC® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL

OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED

BY THIS DOCUMENT. EXCEPT AS EXPLICITLY SET FORTH BELOW OR AS

PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC,

DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC

DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE

AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR

WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,

MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY

RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving, life sustaining, critical

control or safety systems, or in nuclear facility applications.

It is possible that the use or implementation of any one of the concepts, applications, or

ideas described in this document, in marketing collateral produced by or on web pages

maintained by Dialogic Corporation or its subsidiaries may infringe one or more patents

or other intellectual property rights owned by third parties. Dialogic Corporation or its

subsidiaries do not provide any intellectual property licenses with the sale of Dialogic

products other than a license to use such product in accordance with intellectual property

owned or validly licensed by Dialogic Corporation or its subsidiaries. More detailed

information about such intellectual property is available from Dialogic Corporation's legal

department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9.

The software referred to in this document is provided under a Software License

Agreement. Refer to the Software License Agreement for complete details governing the

use of the software.

Dialogic Corporation encourages all users of its products to procure all necessary

intellectual property licenses required to implement any concepts or applications and does

not condone or encourage any intellectual property infringement and disclaims any

responsibility related thereto. These intellectual property licenses may differ from country

to country and it is the responsibility of those who develop the concepts or applications to

be aware of and comply with different national license requirements. Dialogic, Dialogic

Pro, Brooktrout, Cantata, SnowShore, Eicon, Eicon Networks, Eiconcard, Diva,

SIPcontrol, Diva ISDN, TruFax, Realblocs, Realcomm 100, NetAccess, Instant ISDN,

TRXStream, Exnet, Exnet Connect, EXS, ExchangePlus VSE, Switchkit, N20, Powering

The Service-Ready Network, Vantage, Connecting People to Information, Connecting to

Growth and Shiva, among others as well as related logos, are either registered trademarks

or trademarks of Dialogic. Dialogic's trademarks may be used publicly only with

permission from Dialogic. Such permission may only be granted by Dialogic’s legal

department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9.

Any authorized use of Dialogic's trademarks will be subject to full respect of the

trademark guidelines published by Dialogic from time to time and any use of Dialogic’s

trademarks requires proper acknowledgement. The names of actual companies and

products mentioned herein are the trademarks of their respective owner

BRI LED Meaning

Red Layer 1 is down. This can occur if the

cable is wired incorrectly or the CPE

or CO emulation is wrong.

Yellow Layer 1 is up, but layer 2 is down.

This state can occur if the protocol

has not been initialized, the D

channel has not been enabled, or the

clocks have not synchronized.

Green Layer 1 is up, and layer 2 is up.

Red/green The board is currently receiving CRC

errors.

Channel LEDs Meaning

Off Channel is idle.

Flashing green Channel is being set up or is

connected.

No connection

TX Tip 0

RX Tip 0

RX Ring 0

TX Ring 0

No connection

Port A

No connection

TX Tip 1

RX Tip 1

RX Ring 1

TX Ring 1

No connection

Port B

Board Status LED Meaning

Flashing yellow Board is powered up and is

passing self test checks.

Steady red Board is powered up, and the self

test has failed.

Flashing yellow

and green

Board is powered up and is

downloading firmware.

Flashing green Firmware is downloaded, and the

board is in service.

Solid green or

Flickering red

Invalid states. Please reinstall your

board and call Tech Support, if the

condition persists.

Off Board is not powered up.

LED Meaning

DSP Displays the status for the DSP. After the

firmware is loaded and during normal

execution, this LED blinks about every

second. If the LED is not blinking, the DSP

firmware is not running.

Power Steady green indicates good board power.