Specifications

ManualsBrandsDialogic ManualsComputer equipmentBrooktrout TR1034 T1

Connecting to the Telephone Service

An RJ-48C telephone jack on the board mounting

bracket (see Figure 4) provides the connection to the

T1/E1 service.

Figure 4 Front View of Mounting Bracket

The TR1034 Fax Board, when used with a T1 line, is

approved as a DSX-1 device and must be connected

to the telecommunications network through a PBX

or CSU. When used with an E1 line it must be

connected to the SELV (safety extra low voltage)

port of the NTU (network termination unit).

Pinouts for the T1/E1 Connector

Pins 1, 2, 4, and 5 on the RJ-48C telephone jack

provide T1/E1 data paths to and from the board. The

connector pins are configured as shown in the table

below and in (Figure 5).

Figure 5 T1/E1 RJ-48C Pinouts

Dialogic® Brooktrout® Fax Board Status LED

The Board Status LED on the mounting bracket (see

Figure 4) indicates the overall status of the TR1034

Fax Board:

T1/E1 Status LED

The T1/E1 Status LED on the bracket (Figure 4)

represents the T1/E1 service status as shown:

Using the Dialogic® Brooktrout® TR1034 Fax

Board

Once you have installed the TR1034 Fax Board,

install and configure your fax software application

according to instructions included with the software.

After you have set up your software to support the

TR1034 Fax Board, you can send and receive faxes.

Serial Number

You can find the board serial number (2 letters and

9 digits) on white labels on the back of the board.

Getting Help

Dialogic provides technical support for customers

who have purchased hardware or software products

from Dialogic. If you purchased products from a

reseller, please contact that reseller for technical

support. This equipment contains no

user-serviceable parts and is not intended for repair

by unauthorized personnel. If the equipment is

causing harm to the telephone network, the

telephone company might request that you

disconnect the equipment until the problem is

resolved.

To obtain technical support, please use the web site:

http://www.dialogic.com/support

Hardware Limited Warranty

Please refer to the following Dialogic web site for

information on hardware warranty information,

which applies unless different terms have been

agreed to in a signed agreement between yourself

and Dialogic Corporation or its subsidiaries. The

listed hardware warranty periods and terms are

subject to change without notice. For purchases not

made directly from Dialogic please contact your

direct vendor in connection with the warranty period

and terms that they offer.

http://www.dialogic.com/warranties

this document in whole or in part without permission in writing from Dialogic Inc. at the

address provided below.

All contents of this document are furnished for informational use only and are subject

to change without notice and do not represent a commitment on the part of Dialogic

Inc. and its affiliates or subsidiaries (“Dialogic”). Reasonable effort is made to ensure

the accuracy of the information contained in the document. However, Dialogic does not

warrant the accuracy of this information and cannot accept responsibility for errors,

inaccuracies or omissions that may be contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH DIA-

LOGIC PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR

OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU

AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIA-

LOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE

AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES

RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR

INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in certain safety-affecting situations. Please

see http://www.dialogic.com/about/legal.htm

for more details. Due to differing national

regulations and approval requirements, certain Dialogic products may be suitable for

use only in specific countries, and thus may not function properly in other countries.

You are responsible for ensuring that your use of such products occurs only in the

countries where such use is suitable. For information on specific products, contact Dia-

logic Inc. at the address indicated below or on the web at www.dialogic.com.

It is possible that the use or implementation of any one of the concepts, applications, or

ideas described in this document, in marketing collateral produced by or on web pages

maintained by Dialogic may infringe one or more patents or other intellectual property

rights owned by third parties. Dialogic does not provide any intellectual property

licenses with the sale of Dialogic products other than a license to use such product in

accordance with intellectual property owned or validly licensed by Dialogic and no such

licenses are provided except pursuant to a signed agreement with Dialogic. More

detailed information about such intellectual property is available from Dialogic’s legal

department at 1504 McCarthy Boulevard, Milpitas, CA 95035-7405 USA. Dialogic

encourages all users of its products to procure all necessary intellectual prop-

erty licenses required to implement any concepts or applications and does not

condone or encourage any intellectual property infringement and disclaims any

responsibility related thereto. These intellectual property licenses may differ

from country to country and it is the responsibility of those who develop the

concepts or applications to be aware of and comply with different national

license requirements. Dialogic, Dialogic Pro, Dialogic Blue, Veraz, Brooktrout, Diva,

Diva ISDN, Making Innovation Thrive, Video is the New Voice, VisionVideo, Diastar,

Cantata, TruFax, SwitchKit, SnowShore, Eicon, Eiconcard, NMS Communications,

NMS (stylized), SIPcontrol, Exnet, EXS, Vision, PowerMedia, PacketMedia, Border-

Net, inCloud9, I-Gate, ControlSwitch, NaturalAccess, NaturalCallControl, NaturalCon-

ference, NaturalFax and Shiva, among others as well as related logos, are either

registered trademarks or trademarks of Dialogic Inc. and its affiliates or subsidiaries.

Dialogic's trademarks may be used publicly only with permission from Dialogic. Such

permission may only be granted by Dialogic’s legal department at 1504 McCarthy Bou-

levard, Milpitas, CA 95035-7405 USA. Any authorized use of Dialogic's trademarks will

be subject to full respect of the trademark guidelines published by Dialogic from time to

time and any use of Dialogic’s trademarks requires proper acknowledgement.

The names of actual companies and products mentioned herein are the trademarks of

their respective owners.

Signal Name RJ-48C Pin

Transmit (TX) Tip 5

Transmit (TX) Ring 4

Receive (RX) Tip 2

Receive (RX) Ring 1

Board Status LED Indicates

Off Board has no power.

Flashing yellow Board powered up and

ready to load firmware.

Steady red Board powered up, but

failed tests.

Flashing yellow

and green

Board is downloading

firmware.

Flashing green Firmware is downloaded

and the board is ready for

use.

T1/E1 Status LED Indicates

Off The software has not yet

initialized the board with the

telephony configuration.

Green Normal error-free operation; layer

1 is up.

Red Red alarm (loss of incoming

network signal).

Yellow Yellow alarm (transmitting alarm

– board is failing to synchronize

with incoming signal).

Green with

flashing red

Clocking error, bipolar violation,

cyclic redundancy error, or other

error.

RX Ring

RX Tip

No connection

TX Ring

TX Tip

No connection

Indicates