User's Manual

SC14CVMDECT Cordless Voice Module
© 2011 SiTel Semiconductor B.V. Company Confidential 44 August 19, 2011 v1.2.1
14.0 Notices to OEM
14.1 FCC REQUIREMENTS REGARDING THE END
PRODUCT AND THE END USER.
This module is for use only in DECT / UPCS handsets
and base stations.
The antenna(s) used for this transmitter must not be
co-located or operating in conjunction with any other
transmitter
The end product that the module is integrated into must
be marked as follows:
"Contains Transmitter Module FCC ID: Y82-SC14A /
IC: 9576A-SC14A"
The literature provided to the end user must include the
following wording:
FCC compliance statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation of the device.
Module transmetteur ID IC: 9576A-SC14A
Son fonctionnement est soumis aux deux conditions
Suivantes: (1) cet appareil ne doit pas causer
D'interférences nuisibles et (2) appareil doit accepter
Toute interference recue, y compris les interferences
Qui peuvent pertuber le fonctionnement.
Changes or modifications to the equipment not
expressly approved by the Party responsible for
compliance could void the user's authority to Operate
the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generate, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and
receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Privacy of communications may not be ensured when
using this phone.
A separation distance of at least 20 cm must be
maintained between the base station and all persons
(excluding extremities of hands, wrist and feet).
14.2 PRECAUTIONS REGARDING UNINTENDED
COUPLING
The SC14CVMDECT does not have any electrical
Shielding, so by integration on the main board
precautions shall be taken in order to avoid any kind of
coupling from the main board to the RF part of the
module. If there is any doubt about this, a radio short
test should be performed.
14.3 END APPLICATION APPROVAL
The module is intended to be used in an end
application. When the requirements in 14.2 are fulfilled,
no further test concerning the module is needed. Type
approval concerning the end product, except for the
module, should off cause be done. Please contact a
test-house in order to clarify what is needed.
14.4 SAFETY REQUIREMENTS
This section provides of an overview of the safety
requirements you must adhere to when working with
the Cordless Voice Module SC14CVMDECT.
• The specific external power supply for the Cordless
Voice Module SC14CVMDECT has to fulfill the
requirements according to clause 2.5 (Limited power
source) of this standard EN 60950-1:2006.
• Interconnection circuits shall be selected to provide
continued conformance to the requirements of
clause 2.2 for SELV (Safety Extra Low Voltage)
circuits according to EN 60950-1:2006 after making
connections.
• Interface type not subjected to over voltages (i.e.
does not leave the building).
• Requirements additional to those specified in this
standard may be necessary for:
• Equipment intended for operation in special
environments (for example, extremes of
temperature, excessive dust, moisture or vibration,
flammable gases and corrosive or explosive
atmospheres).
• Equipment intended to be used in vehicles, on Board
ships or aircraft, in tropical countries or at altitudes
greater than 2000 m.
• Equipment intended for use where ingress of water
is possible.
• Installation by qualified personnel only!
• The product is a component intended for installation
and use in complete equipment. The final
acceptance of the component is dependent upon its
installation and use in complete equipment.