User's Manual

UM-D-010
DA14AVDDECT System Overview
NDA Confidential
User Manual
Revision 1.2
20-Aug-2020
CFR0012
15 of 18
© 2020 Dialog Semiconductor
Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer
d’interférences nuisibles et (2) appareil doit accepter toute interference recue, y compris les
interferences qui peuvent pertuber le fonctionnement. Changes or modifications to the equipment not
expressly approved by the Party responsible for compliance could void the user's authority to operate
the equipment.
Changes or modifications to the equipment not expressly approved by the Party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital de-
vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interferen-
ce will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV technician for help
Privacy of communications may not be ensured when using this phone.”
The host device shall be properly labelled to identify the modules within the host device. The Industry
Canada certification label of a module shall be clearly visible at all times when installed in the host
device, otherwise the host device must be labelled to display the Industry Canada certification
number of the module, preceded by the words "Contains transmitter module", or the word "Contains",
or similar wording expressing the same meaning, as follows:
Contains Transmitter Module IC: 9576A-DA14AVD
L'appareil hôte doit être étiqueté comme il faut pour permettre l'identification des modules qui s'y
trouvent. L'étiquette de certification d'Industrie Canada d'un module donné doit être posée sur
l'appareil hôte à un endroit bien en vue en tout temps. En l'absence d'étiquette, l'appareil hôte doit
porter une etiquette donnant le numéro de certification du module d'Industrie Canada, précédé des
mots " Contient un module d'émission ", du mot " Contient " ou d'une formulation similaire exprimant
le même sens, comme suit :
Contient le module d'émission IC: 9576A-DA14AVD
This device complies with Industry Canada licence exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
9.4.5 Safety Requirements
This section provides an overview of the safety requirements you must adhere to when working with
DA14AVDDECT.
The specific external power supply for DA14AVDDECT has to fulfil the requirements according to
clause 2.5 (Limited power source) of this standard EN 60950- 1:2006
Interconnection circuits shall be selected to provide continued conformance to the requirements
of clause 2.2 for SELV (Safety Extra Low Voltage) circuits according to EN 60950-1:2006 after
making connections